Arctic Cat Sno Pro 120 2011 Скачать руководство пользователя страница 463

Страница: 463 / 535

7-95

CLEANING AND INSPECTING



NOTE: Whenever a part is worn excessively,

cracked, or damaged in any way, replacement is nec-
essary.

1. Clean the bearings with a clean cloth.

2. Inspect each idler wheel for cracks or damage.

3. Inspect the bushings (located in the arm pivot area)

for wear or damage.

4. Inspect all welds and the tubing of the rear arm/idler

arm for cracks or unusual bends.

5. Inspect the two adjusting cams for damage.

6. Rotate the idler wheel bearings (by hand) and check

for binding or roughness.

7. If a bearing must be replaced, see Idler Wheels/

Mounting Blocks - Cleaning and Inspecting in this

sub-section.

INSTALLING

1. Place the rear arm assembly into position between

the slide rails. Secure with a cap screw and lock nut.

Tighten to 40 ft-lb.

TZ016A

2. Install the rear arm onto the idler arm with an alumi-

num axle and two cap screws. Tighten to 40 ft-lb.

TZ015A

3. With the sleeves installed, install the shock absorber

and links to the mounting hole of the rear shock pivot

with cap screws and lock nuts. Tighten securely.



NOTE: The shock absorber and links must be

secured to the rear shock pivot before installing to
the slide rails.

TZ017A

4. Assemble the rear shock pivot idler wheel assembly

with the axle (A), axle tube (B), axle spacers (C), and

shim washers (if applicable).

TZ014A

5. Install the rear shock pivot/idler wheel assembly to

the mounting location in the slide rails and secure

with cap screws and lock nuts. Tighten to 20 ft-lb.

TZ019

6. With the sleeves installed, install the shock absorber

to the mounting hole of the idler arm along with the

cap screw and lock nut; then secure the shock

absorber links and spacer to the upper mounting hole

of the idler arm with cap screws and lock nuts.

Tighten securely.

Manual

Table of Contents

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Arctic Cat Sno Pro 120 2011, Руководство по обслуживанию, Страница: 463 / 535

Результаты поиска

Содержание Sno Pro 120 2011

Отзывы: