manualshive.com logo in svg

Arctic Cat Sno Pro 120 2011, Руководство по обслуживанию, Страница: 450 / 535

Поделиться
Скачать
Arctic Cat Sno Pro 120 2011 Скачать руководство пользователя страница 450

7-82

FZ079A

NOTE: If binding of the wear strip occurs, use a

pipe wrench, start from either end, and hook the edge
of the wear strip with the pipe wrench jaw and twist
the wear strip off the slide rail. Move the pipe wrench
3 in. and again twist the wear strip off the rail. Repeat
this procedure until the wear strip is free of the rail.

3. Remove the front arm limiter straps from the front

arm of the skid frame.

ZJ270

4. Remove the cap screws securing the two front rail

supports to the slide rail.

FZ080A

5. Remove the cap screws and lock nuts securing the

front outer idler wheel and the idler wheel mounting

block.

FZ081A

FZ057A

6. Remove the lock nut and flat washer securing the

front shock axle assembly to the slide rail. Discard

the lock nut.

FZ058A

NOTE: If removing the cap screws from the front

shock axle is necessary to replace the slide rail,
install the cap screw from the opposite side into the
assembly to secure components and aid in replacing
the slide rail.

7. Remove the lock nut, cap screw, and flat washer

securing the spring slide to the rail. Account for a

spacer and the slide block.

Manual

Table of Contents

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов