Arctic Cat Sno Pro 120 2011 Скачать руководство пользователя страница 93

Страница: 93 / 535

2-55

CM013



NOTE: To ensure the cleanliness of the flywheel

magnets, place the flywheel (with the magnets facing
upward) on a clean bench.

4. Remove the ignition timing sensor.

FC022

5. Remove the Allen-head cap screws securing the sta-

tor to the stator plate. Move the stator to the side to

access the Phillips-head cap screw securing the stator

lead wire; then remove the cap screw.

FC018

6. On the 600 cc, remove the Allen-head cap screws

securing the magneto case to the crankcase. Account

for four alignment pins.



NOTE: Note the different-sized cap screws for

assembling purposes.

FC019

RS020A

7. Remove the stator plate from the engine.

FC021

FC065



NOTE: The stator plate screws had Loctite applied

to the threads during assembly. Using an impact
driver, apply a sharp blow to the head of each screw
to break the Loctite loose before removal.

Manual

Table of Contents

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Arctic Cat Sno Pro 120 2011, Руководство по обслуживанию, Страница: 93 / 535

Результаты поиска

Содержание Sno Pro 120 2011

Отзывы: