Arctic Cat Sno Pro 120 2011 Скачать руководство пользователя страница 371

Страница: 371 / 535

7-3

When riding in sticky snow (springtime or warm days) or

hill climbing on hard snow, it may be desirable to stiffen

the front arm spring tension. When this is done, weight is

transferred back quicker. The problem with too much

front arm spring tension is that the feel of the snowmo-

bile becomes very short. The reason for this is the front

arm becomes the pivot point between the spindles and

rear of the snowmobile. With dominant spring tension on

the front arm, the suspension is basically contacting the

snow from a point below the front arm to the skis or the

spindle pressure point. This makes for a very short and

darting snowmobile on the trail. This is especially true

when decelerating and the center of gravity is transferred

forward.

A good method for adjusting the front spring tension fol-

lows.



NOTE: On those models having a coil spring over

the front arm shock absorber, the spring tension
should be set as soft as possible when operating on
trails and in deep snow.

0729-662

FRONT ARM LIMITER STRAPS

Under no circumstances should the front arm limiter

strap be lengthened. If lengthened, it may cause shock

absorber travel problems.

The two limiter straps can be shortened to suit driving

style and some test driving time. With the rear arm in its

present mounting location, no advantage has been noted

from changing the strap length. If the front arm straps are

shortened, the result will be more ski pressure and

aggressive steering.

SKI SHOCK ABSORBER SPRINGS

The shock absorber springs have been matched to the

shock valving and rear suspension. These springs are the

result of hours of testing and comparison riding trying

many different combinations of springs and shocks. If

changes are necessary, several spring and shock sizes are

available. While making these changes, keep the follow-

ing points in mind.

Heavier Or Stiffer Springs

1. These will require shocks with more rebound con-

trol, or the front end will become like a pogo stick.

2. With stiffer springs, the front end will become more

aggressive in the corners as more weight will be

transferred to the skis when decelerating. Also, more

weight is transferred to the rear on acceleration and

can cause the rear shocks and spring to bottom out.

3. If the springs are too stiff for general riding condi-

tions and style, the ride comfort is gone.

Spring Tension Too Soft

1. Front end bottoms out; hard on front end parts.

2. Less aggressive steering in corners on deceleration,

and less weight is transferred to the skis because of

softer springs.

3. Less weight gets transferred to rear of the machine

upon acceleration.



NOTE: When softening the ski springs, also soften

the rear to match entire suspension.

ADJUSTING FRONT SHOCKS (Fox
Air Shocks)

The air shocks are individually adjustable for the terrain

conditions and driving style of the operator. The ski

shocks are initially preset at the factory (see Section 1).

However, the shocks can be “fine tuned” to match the

operator’s weight, riding style, and terrain conditions.



NOTE: Care should be taken to have equal pressure

in the shocks before operating the snowmobile.

To increase or decrease air pressure, use the following

procedure.



NOTE: Adding air pressure will increase the air

spring force; reducing air pressure will decrease air
spring force.

1. Remove the air valve cap from the shock.

2. Thread the valve of Shock Absorber Air Pump onto

the shock air valve approximately six rotations.



NOTE: As the pump is being attached to the shock,

the hose will fill with air resulting in a lower gauge

pressure 0.14-3.52 kg/cm

(2-5 psi).

3. To decrease air pressure in the shock, press the black

bleed valve button half way down and hold until

desired pressure is attained.



NOTE: Pressing the button fully down and releasing

it will allow only a small amount of air to escape
(micro-adjust).

CAUTION

If the ski shock spring is adjusted too loose, the
spring retainer may fall out. If the spring is adjusted
beyond specification, the spring will coil bind and
spring adjuster damage will occur.

! WARNING

Do not exceed 105 kg/cm

(150 psi) in the shock.

Manual

Table of Contents

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Arctic Cat Sno Pro 120 2011, Руководство по обслуживанию, Страница: 371 / 535

Результаты поиска

Содержание Sno Pro 120 2011

Отзывы: