Arctic Cat Sno Pro 120 2011 Скачать руководство пользователя | Manualshive

Страница: 516 / 535

background image

8-26

ZJ174A

6. Install the shock absorber to the spindle; then install

the cap screw and lock nut. Tighten to 32 ft-lb.

7. On the Z1, install the front bumper to the chassis;

then secure the bumper to the side panels with the

two self-tapping screws.

ZJ166B

8. On the Z1, install the two body screws and lock nuts

securing the bottom of the bumper assembly to the

chassis; then install the hood.

ZJ167A



NOTE: On the liquid-cooled F-Series to finalize the

installing of the lower A-arms, proceed to Air Silencer
(Liquid-Cooled F-Series 2-Stroke) sub-section in Sec-
tion 3 and follow the INSTALLING procedure.

Front Suspension (Ski)

Shock Absorber

REMOVING

1. Position the front of the snowmobile up onto a safety

stand taking all pressure off the skis.

2. Remove the cap screws securing the shock absorber

to the front end assembly and spindle; then remove

the shock absorber. Account for all mounting hard-

ware.



NOTE: Note the number of threads exposed

between the spring adjuster and shock housing for
installing purposes.

3. Using the Shock Spring Removal Tool, remove the

spring from the shock body by compressing the

spring; then remove the spring retainer from the top

of the spring. Inspect the shock absorber by quickly

compressing and extending the shock plunger while

firmly holding the shock body. Resistance must be

felt in both directions.

CLEANING AND INSPECTING



NOTE: Whenever a part is worn excessively,

cracked, or damaged in any way, replacement is nec-
essary.

1. Inspect the shock absorber seal area for signs of

excessive oil leakage.

2. Inspect the shock absorber mounting eyelet, bush-

ings, and sleeve for wear or damage.

3. Inspect the threaded shock sleeve for damage or

wear. Clean the sleeve and apply a light coat of

grease to the threads before installing.

INSTALLING

1. Using the shock spring tool, place the spring on the

shock absorber and secure with the retainer.

2. Adjust the retainer nut (spring adjuster) (if applica-

ble) until the specified amount of threads are

exposed between the spring adjuster and the shock

housing (noted in removing) as an initial setting.

3. Install the bushings, sleeves, and spacers into each

shock end; then place the shock absorber into posi-

tion. Install both cap screws from the front. Tighten

the lock nuts to 20 ft-lb (Bearcat/Crossfire/M-Series)

or 32 ft-lb (F-Series/T-Series).

Sway Bar (CFR/Crossfire)

REMOVING

1. Remove the lock nuts and cap screws securing the

sway bar arm to the links and remove.

Manual

Table of Contents

«
...
514
515
516
517
518
...
»

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды