Arctic Cat Sno Pro 120 2011 Скачать руководство пользователя страница 160

Страница: 160 / 535

2-122

ZJ075



NOTE: Rotate the crankshaft one revolution to ver-

ify free movement.

13. With the O-ring lubricated with engine oil, install the

oil-relief valve.

ZJ076A



NOTE: Prior to installing the oil-relief valve, make

sure the valve is free and clear of any contaminants.

14. With proper bearings selected, install the counterbal-

ancer bearing halves into the upper engine case; then

apply a light film of engine-assembly grease to the

bearing surfaces.

15. Rotate the crankshaft to the bottom-dead-center posi-

tion; then install the rear counterbalancer with the

two dots (A) on the face of the crankshaft and bal-

ancer gears directly in line with each other at the

sealing surface of the engine case.



NOTE: The front counterbalancer has the oil pump

drive gear.

741-596A

16. With the crankshaft at bottom-dead-center, install the

front counterbalancer with the single dot (B) on the

face of the crankshaft and balancer gears directly in

line with each other at the sealing surface of the

engine case.

17. Place the oil-passage O-rings (A) into place in the

upper engine case; then install the three alignment

pins (B) into the case.

ZJ042A

ZJ042B

18. Install the separator plates to the lower crankcase;

then using the torque pattern shown, secure with

eight cap screws. Tighten to 84 in.-lb.

741-737A

19. Install the crankshaft and counterbalancer bearing

halves to the lower crankcase; then apply a light film

of engine-assembly grease to the bearing surfaces.



NOTE: Make sure the bearings are properly seated

to the grooves of the crankcase.

20. Using Three Bond Sealant, apply a light film of seal-

ant onto the sealing surfaces of the upper and lower

engine cases.

Manual

Table of Contents

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Arctic Cat Sno Pro 120 2011, Руководство по обслуживанию, Страница: 160 / 535

Результаты поиска

Содержание Sno Pro 120 2011

Отзывы: