Arctic Cat Sno Pro 120 2011 Скачать руководство пользователя

Страница: 201 / 535

3-22

FS236A

4. Place a towel beneath the coolant hose and remove

the hose from the throttle body.

5. Using Vacuum Test Pump and proper-sized hoses,

connect the pump to the throttle body coolant hose.

6. Remove the vise-grip pliers from the coolant hose

and the cap from the coolant tank; then pump the

coolant from the system.

FILLING COOLING SYSTEM

1. Elevate the front of the snowmobile 30-60 cm (12-14

in.).

2. Remove the coolant tank cap and check coolant

level. The coolant tank should be filled to the coolant

level line.

3. Install the coolant tank cap; then start the engine.

Run the engine at 3000-3500 RPM until the bottom

heat exchangers become hot to the touch. Stop the

engine and allow the system to cool.



NOTE: On the F-Series prior to starting the engine,

connect the console/main harness plug-in and place
the console in position. Do not secure the console
with the torx-head screws at this time.

4. Lower the front of the snowmobile and elevate the

rear of the snowmobile 12-14 in. Repeat the proce-

dures in step 3.

5. Check the coolant level. Add coolant as required to

the coolant tank (coolant tank should be filled to

coolant level line). Repeat procedure until coolant

level stabilizes in the coolant tank.



NOTE: If coolant is required, mix coolant for a tem-

perature of -36°C (-34°F). Follow mixing recommen-
dations of the manufacturer of the coolant.



NOTE: At this point, secure the console with the

torx-head screws.

INSPECTING COOLANT HOSES AND
CLAMPS

All coolant hoses and connections should be checked

annually for deterioration, cracks, and wear.

All coolant hoses and clamps should be replaced every

four years.

INSPECTING THERMOSTAT

1. Inspect the thermostat for corrosion, wear, or spring

damage.

2. Using the following procedure, inspect the thermo-

stat for proper operation.

a. Suspend the thermostat in a container filled with

water.

b. Heat the water and monitor the temperature with a

thermometer.

c. The thermostat should open at 30°C (86°F). Once

the thermostat starts to open, remove the thermo-

stat and allow it to cool down verifying it has

returned to the fully closed position.

Liquid Cooling System

(1100 cc)

The liquid cooling system consists of a heat exchanger,

water pump, and thermostat. The system should be

inspected for leaks or damage whenever an overheating

problem is experienced.

DRAINING COOLING SYSTEM

1. Open the right-side access panel.

2. Remove the hairpin clip (non-turbo) and springs

securing the exhaust resonator to the chassis; then

remove the resonator.

3. Remove the hose clamp from the coolant hose (A)

connecting the water pump to the right side of the oil

cooler. Clamp off the coolant hose; then with a drain

pan positioned under the coolant hose, remove the

hose from the water pump and tip the hose down-

ward allowing the coolant to drain completely.

CAUTION

Be sure the cooling system is thoroughly filled using
the following procedure.

CAUTION

The Filling Cooling System procedure must be fol-
lowed very closely and the cooling system must be
properly filled. If the system isn’t properly filled, piston
damage will occur.

CAUTION

Never heat the thermostat to the fully open position or
damage to the thermostat may occur.

Manual

Table of Contents

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды

Arctic Cat Sno Pro 120 2011, Руководство по обслуживанию

Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды