Arctic Cat Sno Pro 120 2011 страница 467 Скачать руководство пользователя

Страница: 467 / 535

7-99

TZ028A

4. Remove the front arm and account for the front arm

axle.

5. Remove the front outer idler wheel and mounting

block from the side of the slide rail in which the front

arm shock axle cap screw was installed.

FZ029A

6. Remove the cap screws, washer, and lock nut from

the front shock axle; then from the side that the idler

wheel and mounting block was removed, tap the

assembly forward far enough for the axle assembly

to clear the slide rails. Account for an axle, two spac-

ers, and two shim washers.

TZ029

TZ030

INSPECTING



NOTE: Whenever a part is worn excessively, cracked,

or damaged in any way, replacement is necessary.

1. Inspect all front arm weldments for cracks or unusual

bends; then inspect the front arm mounting brackets

for cracks and for elongated holes.

2. Closely inspect all tubing for cracks or unusual

bends.

3. Inspect the bearings, bushings, and front arm spacers

for wear or damage.

4. Inspect the shock absorber for damage and for any

signs of oil leakage especially at the point where the

shock shaft enters the shock body.

5. Inspect the shock absorber eyelet welds (at each end)

for any cracks, signs of separation, or for unthreading.

INSTALLING

1. With the rubber bushing in place, install the axle into

the lower shock eyelet bushing assembly; then install

the two shim washers and two spacers.

CM246A



NOTE: Applying a light film of lubricant to the rub-

ber bushing will aid in installing.

2. Position the front arm shock axle assembly on the

skid frame making sure the spacers and washers are

properly positioned. Secure with the cap screw,

washer, and a new lock nut. Tighten to 40 ft-lb.

Manual

Table of Contents

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды

Arctic Cat Sno Pro 120 2011, Руководство по обслуживанию

Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды