manualshive.com logo in svg

Arctic Cat Sno Pro 120 2011, Руководство по обслуживанию

Сервисный мануал Arctic Cat Sno Pro 120 2011 доступен для бесплатного скачивания на {вашем сайте}. Этот руководство поможет вам поддерживать и обслуживать ваш снегоход, обеспечивая надежную работу. Скачайте его прямо сейчас и получите всю необходимую информацию для правильного ухода за вашим транспортным средством.

Поделиться
Скачать
background image

8-20

NOTE: The straightedge should be long enough to

extend from the back of the track to the front of the
ski.

5. Measure the distance from the straightedge to the

left-side ski wear bar bolts in two places: approxi-

mately 7-8 in. in front of the spindle and 7-8 in.

behind the spindle. Record the measurements taken

for the left side.

729-887A

0734-408

6. Place the straightedge against the outside edge of the

track so it lies near the inside edge of the right-side

ski.

7. Measure the distance from the straightedge to the

right-side ski wear bar bolts in two places: 7-8 in. in

front of the spindle and 7-8 in. behind the spindle.

Record the measurements taken for the right side.

8. If ski alignment is not as specified, adjust the align-

ment of the ski(s) not parallel to the straightedge.

ADJUSTING 
(CFR/Crossfire/M-Series)

NOTE: The following procedure can be used to

adjust the alignment of either ski.

1. Secure the idler tie rod in the centered position.

2. Loosen both spindle tie rod jam nuts on the same

side as the ski to be aligned.

3. Using a wrench on the spindle tie rod “flats,” rotate

the spindle tie rod until recommended specification

is attained.

4. Apply blue Loctite #243 to each jam nut thread area;

then tighten the jam nuts against the spindle tie rod to

18 ft-lb.

NOTE: Repeat this procedure on each side (if nec-

essary) until ski toe-out is within specification.

ADJUSTING 
(Bearcat/F-Series/T-Series/Z1)

NOTE: The following procedure can be used to

adjust the alignment of either ski.

To adjust ski alignment, use the following procedure.

1. Secure the steering tie rod in the centered position.

2. Loosen both inner tie rod jam nuts on the same side

as the ski to be aligned.

3. Using a wrench on the spindle tie rod “flats,” rotate

the spindle tie rod until recommended specification

is attained.

4. Apply blue Loctite #243 to each jam nut thread area;

then tighten the jam nuts against the inner tie rod.

Tighten to 13 ft-lb.

NOTE: Repeat this procedure on each side (if nec-

essary) until ski toe-out is within specification.

VERIFYING

1. With the handlebar in the straight-ahead position,

verify ski alignment by measuring across from the

outside edge of the left-side wear bar bolts to the out-

side edge of the right-side wear bar bolts (without

using the straightedge) in two places: approximately

7-8 in. in front of the spindle and 7-8 in. behind the

spindle.

2. The measurement from in front of the spindle to the

outer edge of the wear bar bolts (without using the

straightedge) must not exceed the rear measurement

by more than 1/16-1/4 in. toe-out.

! WARNING

The measurement from the front and rear wear bar
bolts to the straightedge can be equal (ski parallel to
the track), but the front measurement must never be
less (ski toed-in) or poor handling will be experienced.
The front wear bar bolt measurement to the straight-
edge must not exceed the measurement from the rear
wear bar bolt to the straightedge (ski toed-out) by
more than 5/32 in.

! WARNING

Neglecting to lock the tie rod by tightening the jam
nuts may cause loss of snowmobile control and possi-
ble personal injury.

! WARNING

Neglecting to lock the tie rod by tightening the jam
nuts may cause loss of snowmobile control and possi-
ble personal injury.

Manual

Table of Contents

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Sno Pro 120 2011

Yard-Man 315E162-401 Owner'S Manual preview
315E162-401
Бренд: Yard-Man Страницы: 10

Бренды по названию

Популярные бренды

Загрузить еще бренды