Arctic Cat Sno Pro 120 2011 страница 52 Скачать руководство пользователя | Manualshive

Страница: 52 / 535

background image

2-14

IO004A

30. Install the resonator and secure with three springs;

then place the expansion chamber and grafoil gaskets

into position and secure to the exhaust manifold and

resonator with the springs.



NOTE: When installing the exhaust manifold

springs, the long hook portion of the spring must be
attached to the exhaust manifold or premature spring
failure will result.

31. Connect the exhaust temperature sensor plug-in; then

secure the sensor harness to the chassis as noted dur-

ing engine removal.

32. Start the engine and warm up to operating tempera-

ture; then verify that all components are functioning

properly and that coolant is circulating through the

cooling system properly.

33. Allow the engine to cool; then check the coolant

level and add coolant as necessary. Verify the tight-

ening torque of the drive clutch.

CAUTION

After running the engine to the proper operating temper-
ature, shut the engine off; then open the hood and
access panels and inspect for any signs of coolant, gas-
oline, or oil leakage.

CAUTION

Never run the engine with the hood harness discon-
nected or damage to the electrical system will result.

CAUTION

If the engine had a major overhaul or if any major com-
ponent was replaced, proper engine break-in proce-
dures must be followed (see Section 1). If the proper
engine break-in procedures are not followed, severe
engine damage may result.

Manual

Table of Contents

«
...
50
51
52
53
54
...
»

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды