Arctic Cat Sno Pro 120 2011 Скачать руководство пользователя страница 215 | Manualshive

Страница: 215 / 535

Arctic Cat Sno Pro 120 2011 Скачать руководство пользователя страница 215

3-36

ZJ009A

7. Install the four cap screws securing the upper bearing

bracket to the upper support plate and tighten to 8 ft-

lb.

ZJ097A

8. Connect the fuel pump four-wire connector; then

secure the knee-pads to the steering support with the

two body screws.

9. Install the upper body panels and secure with the

torx-head cap screws; then install the handlebar

close-off panel and secure it with two torx-head cap

screws.

10. Place the console into position on the headlight sup-

port bracket; then connect the console harness con-

nector.

ZJ098A

11. Secure the console to the chassis with the two torx-

head cap screws.

12. Install the seat to the lowest position; then install the

machine screw (threads coated with blue Loctite

#243) into the seat support assembly and tighten

securely.

Air Silencer

(1100 cc Turbo)



NOTE: Air silencer should be inspected weekly and

seasonally.

REMOVING/INSPECTING

Remove the air cleaner cover; then remove the air filter.

1. Inspect the filter for tears or dirt and replace if neces-

sary.

2. Clean any debris from inside the air intake plenum.

INSTALLING

1. Place the air filter into position into the plenum.

2. Secure the air cleaner cover onto the plenum.

Turbocharger/Intercooler

(1100 cc Turbo)

CAUTION

Do not tighten machine screw against the seat sup-
port. The screw must be loose enough to be effective
as a seat “stop.”

CAUTION

Do not use compressed air to clean the filter. Damage
to the filter may occur.

CAUTION

A torn air filter can cause damage to the turbocharger/
engine. Contaminants may get inside the turbo-
charger/engine if the filter is torn. Carefully examine
the filter for holes or tears. Replace the filter with a
new one if torn.

CAUTION

Do not run the engine without the air filter installed.
Severe damage to the turbocharger/engine will occur.

! WARNING

The rotating components in a turbocharger turn at
speeds of 150,000 RPM. Any imbalance could cause
rapid disintegration resulting in bodily injury or death.
Always handle a turbocharger in accordance with the
manufacturer’s recommendations.

CAUTION

Do not drop the turbocharger. If dropped, it must be
replaced.

CAUTION

Do not touch rotating parts as damage to turbine or
compressor blades may occur.

Manual

Table of Contents

«
...
213
214
215
216
217
...
»

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов