Arctic Cat Sno Pro 120 2011 Скачать руководство пользователя страница 500

Страница: 500 / 535

8-10

0741-924



NOTE: To aid in removing the tie rod cap screws

from the drag link, position the drag link so the cap
screw is aligned with the opening between the skid
plate and the suspension mounting bracket.

ZJ159A

4. Remove the cap screws and lock nuts (C) from the

steering arms (D); then remove the drag link and

steering arms from the suspension mounting bracket.

5. Secure the drag link in a suitable vise; then remove

the cap screws and lock nuts (E) securing the steer-

ing arms to the drag link. Remove the arms and

account for the axles (F) inside the steering arms.



NOTE: With the steering arms removed, note the

direction of the steering arms for installing purposes.

ZJ161A

6. If replacing using a suitable punch, drive the two

bearings out of the drag link.

ZJ162

INSPECTING



NOTE: Whenever a part is worn excessively,

cracked, or damaged in any way, replacement is nec-
essary.

1. Inspect the entire drag link (especially in the areas

where the ball joints attach) for any signs of cracks,

wear, or damage.

2. Inspect the bearings and axles for wear or damage.

INSTALLING

1. If the bearings were removed, place the drag link in a

suitable vise and press the bearings into the drag

link.

ZJ163A

2. Secure the steering arms to the drag link with the

drag link axles, cap screws (E) (threads coated with

blue Loctite #243), and new lock nuts (E). Tighten to

12 ft-lb (Bearcat/F-Series/T-Series) or 120 in.-lb

(Z1).

0741-924

Manual

Table of Contents

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Arctic Cat Sno Pro 120 2011, Руководство по обслуживанию, Страница: 500 / 535

Результаты поиска

Содержание Sno Pro 120 2011

Отзывы: