Arctic Cat Sno Pro 120 2011 Скачать руководство пользователя

Страница: 505 / 535

8-15

CM269A

5. Install the ski.

6. Remove the safety stand from beneath the front end.

Spindle (Bearcat/F-Series/

T-Series/Z1)

REMOVING

1. Position the front of the snowmobile up on a safety

stand.

2. Remove the ski.

3. Remove the tie rod cap and lock nut securing the tie-

rod ball joint to the spindle; then remove the ball

joint from the spindle.



NOTE: Note whether the tie rod is installed on the

top side or on the bottom side of the spindle arm for
installing purposes.

4. Remove the cap and snap ring from the top of the

spindle; then remove the cap screw securing the

spindle arm to the spindle. Remove the spindle arm

and account for and note the number of thrust wash-

ers for installing purposes.

ZJ172

ZJ177



NOTE: The cap screw must be removed to remove

the spindle from the spindle housing.

5. Using a soft hammer and a suitable driving tool,

drive the spindle out of the spindle housing.

6. Remove the lock nut and cap screw securing the

shock absorber to the spindle. Account for all mount-

ing hardware.

ZJ173A

7. Remove the four torx-head cap screws securing the

lower A-arm retainer to the spindle; then remove the

cap and lower arm from the spindle.

ZJ174A

8. Remove the cap screw and lock nut securing the

spindle to the upper suspension arm. Account for all

mounting hardware.

INSPECTING



NOTE: Whenever a part is worn excessively,

cracked, or damaged in any way, replacement is nec-
essary.

Manual

Table of Contents

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды

Arctic Cat Sno Pro 120 2011, Руководство по обслуживанию

Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды