Arctic Cat Sno Pro 120 2011 страница 119 Скачать руководство пользователя

Страница: 119 / 535

2-81

CM158

24. Lift the bottom half of the crankcase off the top half.

25. Lift the crankshaft free from the top half of the

crankcase and slide the crankshaft oil seals off the

crankshaft. Account for the C-ring (A). Remove the

bearing retaining pins (B) and account for the crank-

case dowel pins (C).

IO023A

CM165C



NOTE: The end bearings are not pressed onto the

crankshaft. After removing the seals, use care not to
allow the bearings to slide off the crankshaft.

26. Remove the oil-injection pump/water pump drive-

shaft from the lower crankcase half. Account for the

thrust washer on the outer end of the shaft.

CM159A



NOTE: When replacing the inner water pump seals,

use the recommended Water Pump Bearing and Seal
Tool Kit only.

27. Place the crankcase on the bench with the water

pump side down. Using the long seal driver, drive the

mechanical water pump seal from the crankcase.

FC036

28. Using a pair of snap ring pliers, remove the snap ring

securing the inner seal in the crankcase.

29. Using the hooked end of the tool, pull the inner seal

free of the crankcase.

30. Using the hooked end of the tool, pry the seal ring

from the backside of the water pump impeller.

AN327D

CAUTION

DO NOT drive any tool between halves to separate the
crankcase. Damage to the sealing surfaces will result.

CAUTION

Care must be taken to not allow the connecting rods to
drop onto the sealing surface of the bottom case half.

800 cc

1000 cc

Manual

Table of Contents

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды

Arctic Cat Sno Pro 120 2011, Руководство по обслуживанию

Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды