Arctic Cat Sno Pro 120 2011 страница 210 Скачать руководство пользователя

Страница: 210 / 535

3-31

0743-777

2. Lift the rear of the console and disconnect the con-

sole/main harness plug-in; then remove the console.

3. Remove the springs securing the expansion chamber;

then remove the expansion chamber from the engine

compartment. Account for the two exhaust gaskets.

4. On the LXR Sno Pro with the seat adjusted to its

lowest position, remove the self-tapping screw from

the right-side seat adjustment track; then remove the

seat.

ZJ100A

5. Remove the torx-head screws securing the handlebar

close-off panel; then remove the panel.

6. Remove the lock nuts and torx-head cap screws (A)

securing the right-side front and rear spar panels; then

remove the torx-head screws (D) securing the left-side

rear spar panel to the gas tank and support tube.

742-207A



NOTE: The right-side rear spar panel will remain

secured to the chassis.

7. Remove the cap screw located directly above the

ECU securing the air-silencer duct to the front upper

panel; then disconnect the air temperature sensor and

remove the duct.



NOTE: To aid in accessing the cap screw, the ECU

may be removed.

8. Remove the body screws and flange nuts (C) from

each side securing the front bumper assembly to the

chassis; then remove the two remaining self-tapping

screws (B) from each side securing the front bumper

assembly. Remove the assembly.



NOTE: At this point, remove the air silencer and

account for the rubber exhaust bumper.

CLEANING AND INSPECTING

1. Check for holes or cracks in the silencer.

2. Periodically clean the silencer by blowing fresh air

through it.

3. Inspect the silencer dual intake boot and seals for

cracks or wear.

INSTALLING

1. Install the air silencer onto the throttle bodies making

sure the dual intake boot is properly positioned and

seated.



NOTE: To aid in installing the air silencer, it can be help-

ful to remove the air silencer cover and work the intake
boot over the throttle body from inside the silencer.

FS201A

2. Place the front bumper assembly (with spar panels) into

position on the snowmobile; then secure the front and

rear spar panels together with the torx-head cap screws

and lock nuts (A). Tighten the lock nuts securely.

Manual

Table of Contents

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды

Arctic Cat Sno Pro 120 2011, Руководство по обслуживанию

Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды