Arctic Cat Sno Pro 120 2011 Скачать руководство пользователя страница 51 | Manualshive

Страница: 51 / 535

Arctic Cat Sno Pro 120 2011 Скачать руководство пользователя страница 51

2-13

2

IO003

20. Secure the cables to the servomotor with the cable

holder.

21. Check APV cable adjustment (see Arctic Power

Valve (APV) System in Section 3).



NOTE: Before installing the drive clutch, be sure to

wipe both the crankshaft taper and clutch mounting
taper clean using a clean towel.

22. Apply a few drops of oil to the threads of the drive

clutch cap screw; then place the drive clutch into

position on the crankshaft. Secure with the cap screw

and lock washer. Tighten to 51 ft-lb.



NOTE: Apply a coat of Anti-Seize Thread Com-

pound to the end of the input shaft.

23. Install the alignment washers (if applicable); then

install the driven pulley on the gear case input shaft.

Tighten the cap screw to 32 ft-lb.

CM206

24. Check drive clutch/driven pulley alignment (see Sec-

tion 6).

MS390

25. Install the drive belt. Check belt deflection. Secure

the belt guard (see Section 6).

26. With the air silencer properly positioned on the throt-

tle body assembly, secure the silencer with the torx-

head cap screw.

CM026A

27. Place the hood into position on the front end and

secure with the two pins and the cables.

28. Connect the ignition harness and the hood harness;

then connect the air intake connector.

CM038

29. With the heat shield pad in place, install the heat

shield and secure it to the chassis and oil tank with

the three cap screws; then tighten the two cap screws

to the oil tank to 26 in.-lb. Tighten the remaining cap

screw to 20 ft-lb.

CAUTION

When installing the drive clutch, do not tighten the
clutch cap screw with any kind of impact tool. Tighten
cap screw using a hand torque wrench only. Failure to
do so could result in stationary sheave damage.

CAUTION

Do not allow the driven pulley to “float” on the input
shaft. Damage to the driven pulley will occur.

CAUTION

Do not apply Loctite to the cap screw or damage to the
gear case will occur.

Manual

Table of Contents

«
...
49
50
51
52
53
...
»

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов