Arctic Cat Sno Pro 120 2011 Скачать руководство пользователя страница 72 | Manualshive

Страница: 72 / 535

Arctic Cat Sno Pro 120 2011 Скачать руководство пользователя страница 72

2-34

TZ069A

25. Check APV cable adjustment. See Arctic Power

Valve (APV) System in Section 3.



NOTE: Before installing the drive clutch, be sure to

wipe both the crankshaft taper and clutch mounting
taper clean using a clean towel.

26. Place the drive clutch into position on the crankshaft;

then apply a few drops of oil to the cap screw and

secure with the cap screw and lock washer. Tighten

to 51 ft-lb.

27. Install the alignment washers (if applicable); then

install the driven pulley on the gear case input shaft.

Tighten the cap screw to 32 ft-lb.

FS192

28. Check drive clutch/driven pulley alignment (see Sec-

tion 6). Install the drive belt. Check belt deflection.

Secure the belt guard (see Section 6).

29. Secure the bearing bracket/steering post assembly to

the upper support plate with the bracket plates and

cap screws (coated with blue Loctite #243). Tighten

the cap screws to 96 in.-lb.

FS182A



NOTE: When installing the bracket plates, the wider

end of the plate must be directed up.

FS200A

30. Install the air silencer onto the throttle bodies making

sure the dual intake boot is properly positioned and

seated.



NOTE: To aid in installing the air silencer, it can be

helpful to remove the air silencer cover and work the
intake boot over the throttle body from inside the
silencer.

FS201A

31. Place the front bumper assembly (with spar panels)

into position on the snowmobile; then secure the

front and rear spar panels together with the torx-head

cap screws and lock nuts (A). Tighten the lock nuts

securely.

CAUTION

When installing the drive clutch, do not tighten the
clutch cap screw with any kind of impact tool. Tighten
cap screw using a hand torque wrench only. Failure to
do so could result in stationary sheave damage.

CAUTION

Do not allow the driven pulley to “float” on the input
shaft. Damage to the driven pulley will occur.

CAUTION

Do not apply Loctite to the cap screw or damage to the
gear case will occur.

Manual

Table of Contents

«
...
70
71
72
73
74
...
»

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов