QNAP QTS 4.5 Series User Manual Download Page 42 | Manualshive

Page: 42 / 575

background image

2.

Configure the following settings.

Settings

User Action

Enable configuration reset switch

Select this option to enable the reset button.
For details, see

System Reset and Restore to Factory Default

Enable disk standby mode

Select this option to allow the NAS drives to enter standby
mode if there is no disk access within the specified period. Disk
status LED remains on during standby mode.

Important

The TS-h2490FU NAS does not support disk
standby mode.

Enable light signal alert

Select this option to allow the status LED to flash when free
space on the NAS is less than the set value.

Enable write cache (EXT4 delay
allocation)

If the NAS disk volume uses EXT4, select this option for higher
write performance.
If the NAS is set as a shared storage in a virtualized or
clustered envrionment, disable this option.

Note

When this option is enabled, an unexpected
system shutdown may lead to data loss.

Run user-defined processes during
startup

Select this option to run user-defined processes during startup.

Turn on LED

Select this option to turn on the LED, set its brightness level,
and set a schedule for brightness setting.

Note

This function is only applicable for some models.

3.

Click

Apply

.

Configuring Audio Alert Settings

1.

Go to

Control Panel

>

System

>

Hardware

>

Audio Alert

.

2.

Configure any of the following settings.

Setting

Description

System operations

Select this option to trigger an audio alert every time the NAS
starts, shuts down, or upgrades firmware.

System events

Select this option to trigger an audio alert when errors or
warnings occur.

Enable speech notification

Select this option to replace some audio alerts with speech. You
can select a language and modify the volume.

Tip

Click

Test

to check the modified speech settings.

If there is no sound, another app may be using
the speaker.

3.

Click

Apply

.

QTS 4.5.x User Guide

System Settings

41

«
...
40
41
42
43
44
...
»

Summary of Contents for QTS 4.5 Series
































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for QTS 4.5 Series

Brand: Lifetime Pages: 32

Brand: Extreme Tools Pages: 2

Brand: G-Technology Pages: 33

Brand: Storageflex Pages: 134

Brand: Beta Pages: 7

Ultrastar 15K73

Brand: Hitachi Pages: 273

Travelstar 5K500

Brand: Hitachi Pages: 5

Travelstar 5K500.B

Brand: Hitachi Pages: 5

Travelstar 40GN

Brand: Hitachi Pages: 2

Travelstar 4K40

Brand: Hitachi Pages: 2

Travelstar 4K80

Brand: Hitachi Pages: 2

Travelstar 5K1000

Brand: Hitachi Pages: 2

Travelstar C4K60

Brand: Hitachi Pages: 4

Brand: Hitachi Pages: 4

Travelstar 5K500

Brand: Hitachi Pages: 2

Travelstar 4K40

Brand: Hitachi Pages: 2

Brand: Hitachi Pages: 4

Travelstar 5K120

Brand: Hitachi Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands