QNAP QTS 4.5 Series User Manual Download Page 195 | Manualshive

Page: 195 / 575

background image

1.

Go to

Storage & Snapshots

>

Storage

>

Storage/Snapshots

.

2.

Select a static volume.

3.

Click

Manage

.

The

Volume Management

window opens.

4.

Click

Expand

.

The

Expanding Static Volume Wizard

window opens.

5.

Select

Create and add a new RAID group

.

6.

Click

Next

.

7.

Optional: Select an expansion unit from the

Enclosure Unit

list.

Important

If the expansion unit is disconnected from the NAS, the storage pool becomes inaccessible until
it is reconnected.

8.

Select one or more disks.

Warning

All data on the selected disks will be deleted.

9.

Select a RAID type.
QTS displays all available RAID types and automatically selects the most optimized RAID type.

Important

• If the storage pool contains a RAID 1, RAID 5, RAID 6 or RAID 10 group, the new RAID

group must also have one of the mentioned RAID types.

• For RAID 50 or RAID 60, you cannot select a different RAID type.

10.

Optional: Select the disk that will be used as a hot spare for this RAID group.
For details, see

Configuring a RAID Group Hot Spare

11.

Click

Next

.

12.

Optional: Configure SSD over-provisioning.
Over-provisioning reserves a percentage of SSD storage space on each disk in the RAID group to
improve write performance and extend the disk's lifespan. You can decrease the amount of space
reserved for over-provisioning after QTS has created the RAID group.

Tip

To determine the optimal amount of over-provisioning for your SSDs, download and run SSD
Profiling Tool from App Center.

13.

Click

Next

.

14.

Click

Expand

.

A confirmation message appears.

15.

Click

OK

.

QTS creates the new RAID group and then starts rebuilding the volume. The capacity of the volume
increases after RAID rebuilding is finished.

QTS 4.5.x User Guide

Storage & Snapshots

194

«
...
193
194
195
196
197
...
»

Summary of Contents for QTS 4.5 Series
































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for QTS 4.5 Series

Brand: EAST OAK Pages: 11

Brand: LaCie Pages: 48

Brand: E-Z-RECT Pages: 2

Brand: oldfields Treco Pages: 28

QuantaGrid D51PH-1ULH

Brand: QCT Pages: 167

Brand: Husky Pages: 4

Brilliant by Design Deck Box DB7000

Brand: Suncast Pages: 12

Barracuda 36ES2 ST318418N

Brand: Seagate Pages: 2

Brand: IBM Pages: 141

Brand: SanDisk Pages: 1

FARTOOLS BRICO WB 100

Brand: Far Group Pages: 8

Traveling Disk U260

Brand: PQI Pages: 7

CADT-U32A Series

Brand: Cavalry Pages: 20

Brand: Costway Pages: 15

Brand: Costway Pages: 16

WD1200AVBS - AV

Brand: Western Digital Pages: 3

Brand: QNAP Pages: 16

Brand: QNAP Pages: 39

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands