QNAP QTS 4.5 Series User Manual Download Page 213 | Manualshive

Page: 213 / 575

background image

• If the expansion unit is disconnected from the NAS, the storage pool becomes inaccessible

until it is reconnected.

5.

Select

Create SED secure storage pool

.

The list of disks only displays SED disks.

6.

Select one or more disks.

Warning

All data on the selected disks will be deleted.

7.

Select a RAID type.
QTS displays all available RAID types and automatically selects the most optimized RAID type.

Number of disks

Supported RAID Types

Default RAID Type

One

Single

Single

Two

JBOD, RAID 0, RAID 1

RAID 1

Three

JBOD, RAID 0, RAID 5

RAID 5

Four

JBOD, RAID 0, RAID 5, RAID 6, RAID 10

RAID 5

Five

JBOD, RAID 0, RAID 5, RAID 6

RAID 6

Six or more

JBOD, RAID 0, RAID 5, RAID 6, RAID 10, RAID 50

Note

RAID 10 requires an even number of disks.

RAID 6

Eight or more

JBOD, RAID 0, RAID 5, RAID 6, RAID 10, RAID 50,
RAID 60

RAID 6

Tip

Use the default RAID type if you are unsure of which option to choose.
For details, see

.

8.

Optional: Select the disk that will be used as a hot spare for this RAID group.
The designated hot spare automatically replaces any disk in the RAID group that fails.
For RAID 50 or RAID 60, a spare disk must be configured later. You should configure a global spare
disk so that all subgroups share the same spare disk.

9.

Optional: Select the number of RAID 50 or RAID 60 subgroups.
The selected disks are divided evenly into the specified number of RAID 5 or 6 groups.

• A higher number of subgroups results in faster RAID rebuilding, increased disk failure tolerance,

and better performance if all the disks are SSDs.

• A lower number of subgroups results in more storage capacity, and better performance if all the

disks are HDDs.

Warning

If a RAID group is divided unevenly, the excess space becomes unavailable. For example, 10
disks divided into 3 subgroups of 3 disks, 3 disks, and 4 disks will provide only 9 disks of
storage capacity.

10.

Click

Next

.

11.

Optional: Configure SSD over-provisioning.

QTS 4.5.x User Guide

Storage & Snapshots

212

«
...
211
212
213
214
215
...
»

Summary of Contents for QTS 4.5 Series
































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for QTS 4.5 Series

System Storage DS4000

Brand: IBM Pages: 184

Starck Mobile USB 3.0

Brand: LaCie Pages: 2

Brand: LaCie Pages: 2

Rugged Thunderbolt

Brand: LaCie Pages: 4

Rugged All-Terrain

Brand: LaCie Pages: 37

LaCinema Classic HD

Brand: LaCie Pages: 81

Brand: LaCie Pages: 4

Brand: Husky Pages: 10

Brand: LaCie Pages: 2

Vertical Modular Paint Storage

Brand: Blueshark Studio Pages: 7

PolySafe Depot Type C

Brand: Denios Pages: 8

OMNISTOR 4000f SERIES

Brand: Rackable Systems Pages: 112

Brand: ABSCO SHEDS Pages: 23

Brand: Wayfair Pages: 22

Barracuda 5400.1 ST340015A

Brand: Seagate Pages: 2

Brand: Maxtor Pages: 63

Brand: Edgestore Pages: 91

Brand: Wampat Pages: 18

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands