manualshive.com logo in svg

Fujitsu MB86R02, Hardware Manual

The Fujitsu MB86R02 Application Note manual is available for free download on manualshive.com. This comprehensive user manual provides detailed instructions and insights on using the MB86R02 product, ensuring users can fully leverage its features and capabilities. Enhance your product experience by accessing this informative manual today.

Share
Download
background image

 

 

15-22 

MB86R02 ‘Jade-D’ Hardware Manual V1.64 
 

 

Restrictions 

When DMA transfer is performed by external (DREQ) and peripheral (IDREQ) requests, there 
are some restrictions for external and peripheral signal pins. 

 

 

1.

 DREQ/IDREQ 

DREQ/IDREQ must be asserted for at least 2 cycles of the AHB clock 

(

HCLK). 

There is no restriction for the timing of the negation of DREQ/IDREQ.   

 

After completing DMA transfer in BC 

×

 TC and asserting DACK/IDACK and DEOP/IDEOP, a 

new transfer request (edge of DREQ/IDREQ) can be accepted for the next DMA transfer.   

 

2.

 DACK/IDACK 

After the DMAC has transferred data to the destination address, DACK/IDACK are asserted 
for 1 cycle of the AHB clock (HCLK). If access to the destination was done correctly, this 
signal is asserted.   
If the destination issues error, retry, or split responses on the AHB bus, this signal is not 
asserted.

 

 
In burst transfer mode, these signals indicate that the DMAC has performed destination 
access properly.   
 

3.

 DEOP/IDEOP 

Basically, DEOP/IDEOP are asserted for 1 AHB clock (HCLK) cycle when the DMAC ends 
DMA transfer properly or abnormally. Abnormal DMA transfer includes the following cases: 

•

  Forced termination by DSTP/IDSTP   

•

  Forced termination by setting 1'b0 to DMACA/EB   

•

  Reception of an error response from the source/destination 

 

4.

 DSTP/IDSTP 

DSTP/IDSTP are used to forcibly terminate DMA transfer and it is permissible to assert them 
during transfer (it is also permissible to assert DSTP/IDSTP while DMA is not transferring 
due to the transfer gap or an interrupt function). 
If these signals are used to forcibly terminate DMA transfer, they are not asserted until 
DEOP/IDEOP are asserted. 

 

5.

 Exceptional operation of DEOP/IDEOP

 

If DSTP/IDSTP are asserted immediately after DREQ/DSTP have been asserted, the DMAC 
may request the bus to execute an IDLE transfer. In this case, the DMAC may assert 
DEOP/IDEOP for 2 cycles or more of the AHB clock (HCLK).

 

The assertion period of DEOP/IDEOP depends on the number of previous master transfer 
cycles. Figure 15-4 shows an example of this exception operation. 
 

 

Summary of Contents for MB86R02





























































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MB86R02

Campbell CR10 PROM Replacement Procedure preview
CR10 PROM
Brand: Campbell Pages: 8
Danfoss VLT AQUA Drive FC 202 Installation Manual preview
VLT AQUA Drive FC 202
Brand: Danfoss Pages: 124
Danfoss AME 55 Installation Manual preview
AME 55
Brand: Danfoss Pages: 2
Danfoss AME 110 NL Datasheet preview
AME 110 NL
Brand: Danfoss Pages: 8
Danfoss AK-CH 650 User Manual preview
AK-CH 650
Brand: Danfoss Pages: 114
Danfoss AME 438 SU Installation Manual preview
AME 438 SU
Brand: Danfoss Pages: 24
Danfoss ECL Comfort 296 Operating Manual preview
ECL Comfort 296
Brand: Danfoss Pages: 159
Danfoss VLT AutomationDrive FC 301 Operating Manual preview
VLT AutomationDrive FC 301
Brand: Danfoss Pages: 78
Danfoss AME 335 Installation Manual preview
AME 335
Brand: Danfoss Pages: 20
Danfoss CCR2 Installation Manual preview
CCR2
Brand: Danfoss Pages: 64
Maguire Products GRAVIMETRIC AUGER FEEDER MGF-ST Instruction Manual preview
GRAVIMETRIC AUGER FEEDER MGF-ST
Brand: Maguire Products Pages: 47
Magtrol DSP7000 User Manual preview
DSP7000
Brand: Magtrol Pages: 160
York CIW01 Installation & Maintenance Manual preview
CIW01
Brand: York Pages: 24
ITALFARAD RC4 Operating Instructions Manual preview
RC4
Brand: ITALFARAD Pages: 32
Linear Technology LTC3703 Manual preview
LTC3703
Brand: Linear Technology Pages: 32
Sunricher SR-ZG9001T-RGBW Manual preview
SR-ZG9001T-RGBW
Brand: Sunricher Pages: 3
TSM DOUBLER2 Instructions For Installing preview
DOUBLER2
Brand: TSM Pages: 2
NCE CAB-04p Operation Manual preview
CAB-04p
Brand: NCE Pages: 4

Brands by name

Popular brands

Load more brands