manualshive.com logo in svg

Fujitsu MB86R02, Hardware Manual

The Fujitsu MB86R02 Application Note manual is available for free download on manualshive.com. This comprehensive user manual provides detailed instructions and insights on using the MB86R02 product, ensuring users can fully leverage its features and capabilities. Enhance your product experience by accessing this informative manual today.

Share
Download
background image

 

 

15-20 

MB86R02 ‘Jade-D’ Hardware Manual V1.64 
 

 

 

15.7.1.2 

Limitations with I2S DMA 

The I2S unit is only able to handle a subset of the DMA transfer modes that the DMA Controller 
supports. For this reason, please take note of the following: 
 

 

Threshold values in the I2SxINTCNT register (I2S, offset 0x20) must match the BC values of 
the respective DMAC register DMACAx (DMACA0 ... DMACA7, various offsets) 

 

Each block matches one transfer request 

 

The selected DMAC transfer mode must be 'Block Transfer' (check the DMACBx registers) 

 

Demand and burst transfer modes can not be used with I2S 

 
In order for DMA transfers to work with the I2S unit, each transfer has to transmit/receive as 
many words to/from FIFO as there are valid entries. When DMA has finished, the same setup for 
the next transfer has to be configured again in the DMAC and in the I2S module. 

Summary of Contents for MB86R02





























































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MB86R02

Bartlett Genesis LT3140 Technical Manual preview
Genesis LT3140
Brand: Bartlett Pages: 5
Garmin TR-1 Gold Installation Instructions preview
TR-1 Gold
Brand: Garmin Pages: 4
Epsolar eTracer ET4415BND Operation Manual preview
eTracer ET4415BND
Brand: Epsolar Pages: 44
Watlow EZ-ZONE PM L AAAAB Series User Manual preview
EZ-ZONE PM L AAAAB Series
Brand: Watlow Pages: 30
Z-Wave AC MASTER LITE Installation Manual preview
AC MASTER LITE
Brand: Z-Wave Pages: 27
Xvent ELEMENTAIR B-MARK I Operation And Installation Instructions Manual preview
ELEMENTAIR B-MARK I
Brand: Xvent Pages: 9
Badger Meter MDS 2000 User Manual preview
MDS 2000
Brand: Badger Meter Pages: 66
Hamamatsu C7557 Instruction Manual preview
C7557
Brand: Hamamatsu Pages: 50
M-system EAR70 Instruction Manual preview
EAR70
Brand: M-system Pages: 8
S&S Northern Merlin 500S User Manual preview
Merlin 500S
Brand: S&S Northern Pages: 8
Danfoss AMD 613 Installation Manual preview
AMD 613
Brand: Danfoss Pages: 2
Salus PC12HW Manual preview
PC12HW
Brand: Salus Pages: 2
Base Line BaseStation 1000 Quick Start Manual preview
BaseStation 1000
Brand: Base Line Pages: 11
Hayward HRSN2 series Installation, Operation And Maintenance Instructions preview
HRSN2 series
Brand: Hayward Pages: 36
Nanite systems DAX/2 Instructions Manual preview
DAX/2
Brand: Nanite systems Pages: 41
Advantech ADAM-5511 Manual preview
ADAM-5511
Brand: Advantech Pages: 340
NDS Dometic EM12-150 Installation And Operating Manual preview
Dometic EM12-150
Brand: NDS Pages: 462
Danfoss AK-PC 572 Instructions Manual preview
AK-PC 572
Brand: Danfoss Pages: 16

Brands by name

Popular brands

Load more brands