Fujitsu MB86R02 Hardware Manual Download Page 177

Page: 177 / 892

9-9

MB86R02 ‘Jade-D’ Hardware Manual V1.64

Table 9-5 List of register of IRC0

Address

Register name

Abbreviation

Explanation

Base

Offset

FFFF_FE00

FFFE_8000

+ 00

IRQ flag register

IRQF

Control of IRQ interrupt flag

+ 04

IRQ mask register

IRQM

The mask of the assert of the IRQ interrupt is controlled.

+ 08

Interrupt level mask register

ILM

The interrupt level said to be valid from the ARM core is

set.

+ 0C

ICR monitoring register

ICRMN

The interrupt level of a current IRQ interrupt source is

displayed.

+ 10

Hold request cancellation

level register

HRCL

The hold request cancellation level is set.

+ 14

Delay interrupt control

DICR

The delay interrupt for the task switch is controlled.

+ 18

(Reserved)

It is a reserved area. (access prohibited)

+ 1C

Table base register

TBR

The upper address of the IRQ vector (24 bits) is set.

+ 20

Interrupt vector register

VCT

Display the interrupt vector table.

+ 24

IRQ test register

IRQTEST

The test of interrupt controller's IRQ interrupt function is

controlled.

+ 28

FIQ test register

FIQTEST

+ 2C

(Reserved)

It is a reserved area. (access prohibited)

+ 30

Interrupt control register 0

ICR00

The level of the IRQ0 interrupt is set (unused and access

prohibited).

+ 34

Interrupt control register 1

ICR01

The level of the IRQ1 interrupt is set (unused and access

prohibited).

+ 38

Interrupt control register 2

ICR02

The level of the IRQ2 interrupt is set (unused and access

prohibited).

+ 3C

Interrupt control register 3

ICR03

The level of the IRQ3 interrupt is set (unused and access

prohibited).

+ 40

Interrupt control register 4

ICR04

The level of the IRQ4 interrupt is set (unused and access

prohibited).

+ 44

Interrupt control register 5

ICR05

The level of the IRQ5 interrupt is set (IRC2 interrupt).

+ 48

Interrupt control register 6

ICR06

The level of the IRQ6 interrupt is set (IRC1 interrupt).

+ 4C

Interrupt control register 7

ICR07

The level of the IRQ7 interrupt is set (GPIO interrupt).

+ 50

Interrupt control register 8

ICR08

The level of the IRQ8 interrupt is set (ADC ch.0 interrupt).

+ 54

Interrupt control register 9

ICR09

The level of the IRQ9 interrupt is set (ADC ch.1 interrupt).

+ 58

Interrupt control register 10

ICR10

The level of the IRQ10 interrupt is set (external interrupt

0).

+ 5C

Interrupt control register 11

ICR11

The level of the IRQ11 interrupt is set (external interrupt

1).

+ 60

Interrupt control register 12

ICR12

The level of the IRQ12 interrupt is set (external interrupt

2).

+ 64

Interrupt control register 13

ICR13

The level of the IRQ13 interrupt is set (external interrupt

3).

+ 68

Interrupt control register 14

ICR14

The level of the IRQ14 interrupt is set (timer ch.0

interrupt).

+ 6C

Interrupt control register 15

ICR15

The level of the IRQ15 interrupt is set (timer ch.1

interrupt).

+ 70

Interrupt control register 16

ICR16

The level of the IRQ16 interrupt is set (DMAC ch.0

interrupt).

+ 74

Interrupt control register 17

ICR17

The level of the IRQ17 interrupt is set (DMAC ch.1

interrupt).

Summary of Contents for MB86R02





























































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for MB86R02

Reviews:

Related manuals for MB86R02

Brands by name

Popular brands

Fujitsu MB86R02, Hardware Manual

Search results

Summary of Contents for MB86R02

Reviews:

Related manuals for MB86R02

Brands by name

Popular brands