manualshive.com logo in svg

Infineon Technologies TC1784, User Manual

Share
Download
Infineon Technologies TC1784 User Manual Download Page 939

TC1784

Direct Memory Access Controller (DMA)

 

User´s Manual

11-121

V1.1, 2011-05

DMA, V3.03

 

The DMA controller module contains in total 12 interrupt request nodes with its interrupt
service request control registers:
•

Eight interrupt requests SR[7:0] = INT_O[7:0] from the DMA controller; upper eight
interrupt requests of the DMA controller INT_O[15:8] are used ad DMA channel
trigger inputs

.

•

Four interrupt requests SR[3:0] = INT_O[3:0] from the MLI0 module; upper four
interrupt requests of the MLI0 module INT_O[7:4] are not connected.

Figure 11-30 Implementation of the DMA Module and the MLI Module

DMA

Module

Kernel

Interrupt

Control

in DMA

Module

Clock

Control

Address

Decoder

MCA06178

INT_O[15:0]

f

MLI0

f

DMA

MLI0

Module

Kernel

Cerberus

INT_O[7:0]

MLI0_FDR

f

FPI

SR[7:0]

SR[3:0]

16

8

1

CBS_SRC

Summary of Contents for TC1784















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands