manualshive.com logo in svg

Infineon Technologies TC1784, User Manual

Share
Download
Infineon Technologies TC1784 User Manual Download Page 1551

TC1784

FlexRay™ Protocol Controller (E-Ray)

 

User´s Manual

20-175

V1.1, 2011-05

E-Ray, V3.13

 

20.5.2.10 Output Buffer

Double buffer structure consisting of Output Buffer Host and Output Buffer Shadow.
Used to read out Message Buffers from the Message RAM. While the Host can read from
Output Buffer Host, the Message Handler transfers the selected Message Buffer from
Message RAM to the respective Output Buffer Shadow. The data transfer between
Message RAM and Output Buffer (OBF) is described in 

“Data Transfer from Message

RAM to Output Buffer” on Page 20-231

.

Read Data Section [1

…

64] (RDDSn)

The Read Data Section nn (RDDSnn, nn = 01-64) holds the data words read from the
Data Section of the addressed Message Buffer. The data words are read from the
Message RAM in reception order from DW1 (byte0, byte1) to DW

PL

 (PL = number of data

words as defined by the Payload Length).

Note: DW127 is located on RDDS64.MDW. In this case RDDS64.MDW is unused (no

valid data). The Output Buffer RAMs are initialized to zero when leaving
application reset or by CHI command CLEAR_RAMS.

RDDSnn (nn = 01-64)
Read Data Section nn

(05FC

H

+ nn * 4)

Reset Value: 0000 0000

H

31

30

29

28

27

26

25

24

23

22

21

20

19

18

17

16

MDRB3

MDRB2

rh

rh

15

14

13

12

11

10

9

8

7

6

5

4

3

2

1

0

MDRB1

MDRB0

rh

rh

Field

Bits

Type Description

MDRB0

[7:0]

rh

32-Bit Word nn, Byte 0

MDRB1

[15:8]

rh

32-Bit Word nn, Byte 1

MDRB2

[23:16] rh

32-Bit Word nn, Byte 2

MDRB3

[31:24] rh

32-Bit Word nn, Byte 3

Summary of Contents for TC1784















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands