manualshive.com logo in svg

Infineon Technologies TC1784, User Manual

Share
Download
Infineon Technologies TC1784 User Manual Download Page 404

TC1784

On-Chip System Buses and Bus Bridges

 

User´s Manual

4-36

V1.1, 2011-05

Buses, V1.9

 

OCDS Debug Example 3

•

Task: Generation of a BCU debug trigger event on any access into address area
01FFFFFF

H

 to FFFFFFFF

H

 by the PCP.

For this task the following programming settings for the BCU breakpoint logic must be
executed:
1. Writing SBCU_DBADR1 = 01FFFFFF

H

2. Writing SBCU_DBADR2 = don’t care
3. Writing SBCU_DBCNTL = 00215010

H

:

a) ONBOS[3:0] = 0000

B

 means that a signal status trigger is generated for all

FPI Bus opcodes not equal to a “no operation” opcode.

b) ONA2 = 00

B

 means that no address 2 trigger is generated.

c) ONA1 = 10

B

 means that the address 1 trigger is generated if the FPI Bus address

is greater or equal to SBCU_DBADR1.

d) ONG = 1 means that the grant debug trigger is enabled.
e) CONCOM[2:0] = 101

B

 means that the address trigger is created by address

trigger 1 OR address trigger 2 (CONCOM1 = 0), and that the grant trigger is AND-
ed with the address trigger (CONCOM0 = 1), and that the signal status trigger is
ANDed with the address trigger (CONCOM2 = 1).

f) RA = 1 means that the BCU breakpoint logic is rearmed.

4. Writing SBCU_DBGRNT = FFFFFFF7

H

:

means that the grant trigger for the SPB bus master of the PCP is enabled.

5. Writing SBCU_DBBOS is “don’t care”. No signal trigger for SVM, WR, or RD is

generated.

Summary of Contents for TC1784















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands