manualshive.com logo in svg

Infineon Technologies TC1784, User Manual

Share
Download
Infineon Technologies TC1784 User Manual Download Page 286

TC1784

System Control Unit (SCU)

 

User´s Manual

3-103

V1.1, 2011-05

32-bit SCU, V1.18

 

The External Input Flag Register EIFR contains all status flags for the external input
channels. The bits in this register can be cleared by software by setting FMR.FCx, and
set by setting FMR.FSx.

LDEN3

26

rw

Level Detection Enable 3

This bit determines if bit INTF3 is cleared 
automatically if an edge of the input Input Channel 3 
is detected, which has not been selected (rising edge 
with REN3 = 0 or falling edge with FEN3 = 0).
0

B

Bit INTF3 will not be cleared

1

B

Bit INTF3 will be cleared

EIEN3

27

rw

External Interrupt Enable 3

This bit enables the generation of a trigger event for 
request channel 3 (e.g. for interrupt generation) when 
a selected edge is detected.
0

B

The trigger event is disabled

1

B

The trigger event is enabled

INP3

[30:28]

rw

Interrupt Node Pointer

This bit field determines the destination (output 
channel) for trigger event 3 (if enabled by EIEN3).
000

B

The event of input channel 3 triggers output 
channel 0 (signal INT30)

001

B

The event of input channel 3 triggers output 
channel 1 (signal INT31)

010

B

The event of input channel 3 triggers output 
channel 2 (signal INT32)

011

B

The event of input channel 3 triggers output 
channel 3 (signal INT33)

100

B

Reserved, do not use this combination

101

B

Reserved, do not use this combination

110

B

Reserved, do not use this combination

111

B

Reserved, do not use this combination

0

[3:0], 
[7:6], 
[19:15], 
[23:22], 
31

r

Reserved

Read as 0; should be written with 0.

Field

Bits

Type Description

Summary of Contents for TC1784















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands