manualshive.com logo in svg

Infineon Technologies TC1784, User Manual

Share
Download
Infineon Technologies TC1784 User Manual Download Page 327

TC1784

System Control Unit (SCU)

 

User´s Manual

3-144

V1.1, 2011-05

32-bit SCU, V1.18

 

Field

Bits

Type Description

AE

0

rh

Watchdog Access Error Status Flag

0

B

No Watchdog access error

1

B

A Watchdog access error has occurred

This bit is set when an illegal Password Access or 
Modify Access to register WDT_CON0 was 
attempted. This bit is only cleared when 
WDT_CON0.ENDINIT is set during a Valid Modify 
Access
However, it is not possible to clear this bit if the WDT 
is in Prewarning Mode.

OE

1

rh

Watchdog Overflow Error Status Flag

0

B

No Watchdog overflow error

1

B

A Watchdog overflow error has occurred

This bit is set when the WDT overflows from FFFF

H

 to 

0000

H

. This bit is only cleared when 

WDT_CON0.ENDINIT is set to 1 during a Valid 
Modify Access.
However, it is not possible to clear this bit if the WDT 
is in Prewarning Mode.

IS

2

rh

Watchdog Input Clock Status Flag

0

B

The timer operation clock is 

f

FPI

/16384 (default 

after Application Reset)

1

B

The timer operation clock is 

f

FPI

/256

This bit is updated with the state of bit WDT_CON1.IR 
after WDT_CON0.ENDINIT is written with 1 during a 
Valid Modify Access to register WDT_CON0.

DS

3

rh

Watchdog Enable/Disable Status Flag

0

B

WDT is enabled (default after Application 
Reset)

1

B

WDT is disabled

This bit is updated with the state of bit 
WDT_CON1.DR after WDT_CON0.ENDINIT is set 
during a Valid Modify Access to register WDT_CON0.

Summary of Contents for TC1784















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands