manualshive.com logo in svg

Infineon Technologies TC1784, User Manual

Share
Download
Infineon Technologies TC1784 User Manual Download Page 853

TC1784

Direct Memory Access Controller (DMA)

 

User´s Manual

11-35

V1.1, 2011-05

DMA, V3.03

 

When a Move Engine 0 source or destination error occurs, additional status bits and bit
fields are provided in the error status register ERRSR to indicate the following two status
conditions:
•

At which On Chip Bus interface a Move Engine 0 error occurred (FPI or LMB)

•

For which DMA channel a Move Engine 0 read or write move error was reported
(LECME0)

These error status bits and bit fields are required by error handler software to detect in
detail at which On Chip Bus interface and DMA channel the Move Engine error has been
generated. ERRSR.FPIER or ERRSR.LMBER is reset when bits CLRE.CFPI0ER or
CLRE.CFPI1ER is respectively set.

Summary of Contents for TC1784















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands