Infineon Technologies TC1784 User Manual Download Page 881

Page: 881 / 2350

TC1784

Direct Memory Access Controller (DMA)

User´s Manual

11-63

V1.1, 2011-05

DMA, V3.03

The bits in the Software Transaction Request Register are used to generate a DMA
transaction request by software.

Note: Register bits marked with “w” are virtual and are not stored in flip-flops. Reading

STREQ returns 0 when read.

DMA_STREQ
DMA Software Transaction Request Register

(018

)

Reset Value: 0000 0000

SCH

Field

Bits

Type Description

SCH0n
(n = 0-7)

Set Transaction Request for DMA Channel 0n

No action.

A transaction for DMA channel 0n is requested.

When setting SCH0n, TRSR.CH0n becomes set to
indicate that a DMA request is pending for DMA channel
0n.

SCH1n
(n = 0-7)

8+n

Set Transaction Request for DMA Channel 1n

No action.

A transaction for DMA channel 1n is requested.

When setting SCH1n, TRSR.CH1n becomes set to
indicate that a DMA request is pending for DMA channel
1n.

[31:16] r

Reserved

Read as 0; should be written with 0.

Summary of Contents for TC1784















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for TC1784

Reviews:

Brands by name

Popular brands

Infineon Technologies TC1784, User Manual

Search results

Summary of Contents for TC1784

Reviews:

Brands by name

Popular brands