manualshive.com logo in svg

Infineon Technologies TC1784, User Manual

Share
Download
Infineon Technologies TC1784 User Manual Download Page 485

TC1784

Program Memory Unit (PMU)

 

User´s Manual

5-58

V1.1, 2011-05

PMU, V1.47

 

Note: The default numbers of wait states represent the slow cases. This is a general

proceeding and additionally opens the possibility to execute higher frequencies
without changing the configuration.

Note: After reset and execution of BootROM startup SW, the read protection control bits

are coded as follows:
DDF, DCF, RPA = “110”: No read protection installed
DDF, DCF, RPA = “001”: Read protection installed; start in internal Flash
DDF, DCF, RPA = “111”: Read protection installed; start not in internal Flash.

EOBM

31

rw

End of Busy Interrupt Mask

0

B

Interrupt not enabled

1

B

EOB interrupt is enabled

0

[7:5], 
19, 
[23:22]

r

Reserved

Read/write zero

Field

Bits

Type Description

Summary of Contents for TC1784















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands