manualshive.com logo in svg

Infineon Technologies TC1784, User Manual

Share
Download
Infineon Technologies TC1784 User Manual Download Page 589

TC1784

General Purpose I/O Ports and Peripheral I/O Lines (Ports)

 

User´s Manual

9-13

V1.1, 2011-05

Ports, V1.1

 

9.2.2

Pad Driver Mode Register

Overview

The pad structure of the TC1784 GPIO lines offers the possibility to select the output
driver strength and the slew rate. These two parameters are controlled by the bit fields
in the pad driver mode register Pn_PDR, independently of input/output and pull-up/pull-
down control functionality as programmed in the Pn_IOCR register. One Pn_PDR
register is assigned to each port.
The GPIO port lines consists of two classes of pads:
Class A1 pins (low speed 3.3 V LVTTL outputs)
Class A2 pins (high speed 3.3 V LVTTL outputs. e.g. for serial outputs)
Depending on the assigned pad class, the 3-bit wide pad driver mode selection bit fields
PDx in the pad driver mode registers Pn_PDR make it possible to select the port line
functionality as shown in 

Table 9-7

. Note that the pad driver mode registers are specific

for each port. Therefore, the Pn_PDR layout is described for each port in the port-
specific sections.
Class A1 pins make it possible to select between medium and weak output drivers. Class
A2 pins make it possible to select between strong/medium/weak output drivers. In case
of strong driver type, the signal transition edge can be additionally selected as
sharp/medium/soft.

Summary of Contents for TC1784















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands