manualshive.com logo in svg

Infineon Technologies TC1784, User Manual

Share
Download
Infineon Technologies TC1784 User Manual Download Page 482

TC1784

Program Memory Unit (PMU)

 

User´s Manual

5-55

V1.1, 2011-05

PMU, V1.47

 

WSECDF

12

rw

Wait State for Error Correction of DFlash

0

B

No additional wait state for error correction

1

B

One additional wait state for error correction 
during read access to Data Flash

IDLE

13

rw

Dynamic Flash Idle

0

B

Normal/standard Flash read operation

1

B

Dynamic idle of Program Flash enabled for 
power saving; static prefetching disabled

Note: In Data Flash, dynamic idle is always enabled

(prefetching not supported).

ESLDIS

14

rw

External Sleep Request Disable

0

B

External sleep request signal input is enabled

1

B

Externally requested Flash sleep is disabled

The ‘external’ signal input is connected with a global 
power-down/sleep request signal from SCU.

SLEEP

15

rw

Flash SLEEP

0

B

Normal state or wake-up

1

B

Flash sleep mode is requested, 

Wake-up from sleep is started with clearing of the 
SLEEP-bit.

RPA

16

rh

Read Protection Activated

This bit monitors the status of the Flash-internal read 
protection. This bit can only be ‘0’ when read 
protection is not installed or while the read protection 
is temporarily disabled with password sequence.
0

B

The Flash-internal read protection is not 
activated. Bits DCF, DDF are not taken into 
account. Bits DCF, DDFx can be cleared

1

B

The Flash-internal read protection is activated. 
Bits DCF, DDF are enabled and evaluated.

Field

Bits

Type Description

Summary of Contents for TC1784















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands