manualshive.com logo in svg

Infineon Technologies TC1784, User Manual

Share
Download
Infineon Technologies TC1784 User Manual Download Page 864

TC1784

Direct Memory Access Controller (DMA)

 

User´s Manual

11-46

V1.1, 2011-05

DMA, V3.03

 

•

SIZE0/SLIZE0 covering the SPRAM , “a” = 17

•

SIZE1/SLIZE1 covering the OVRAM , “a” = 16

•

SIZE2/SLIZE2 covering the LDRAM , “a” = 17

•

SIZE3/SLIZE3 covering the PRAM, “a” = 16

Two sub-range examples (see 

Figure 11-26

):

•

2

3

= 8 sub-ranges are available with SIZE = 100

B

. SLICE[2:0] selects one out of the

eight sub-ranges. SLICE[4:3] is “don’t care”.

•

2

7

= 128 sub-ranges are basically available with SIZEn = 000

B

. SLICEn[4:0] selects

one out of the lowest 32 sub-ranges. The upper 3 x 32 = 96 sub-ranges are not
selectable (fixed address bits a-1 and a-2).

Note: The definition of the fixed address ranges x and the assignment of each sub-range

to one of the fixed address ranges is product-specific. The definitions of the
address ranges for the DMA controller as implemented in the TC1784 are defined
on 

Page 11-112

.

Summary of Contents for TC1784















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands