manualshive.com logo in svg

Infineon Technologies TC1784, User Manual

Share
Download
Infineon Technologies TC1784 User Manual Download Page 67

TC1784

Introduction

 

User´s Manual

1-28

V1.1, 2011-05

Intro, V1.0

 

Figure 1-6

General Block Diagram of the SSC Interface

The SSC supports full-duplex and half-duplex serial synchronous communication up to
45.0 Mbit/s (@ 90 MHz module clock, Master Mode). The serial clock signal can be
generated by the SSC itself (Master Mode) or can be received from an external master
(Slave Mode). Data width, shift direction, clock polarity and phase are programmable.
This allows communication with SPI-compatible devices. Transmission and reception of
data is double-buffered. A shift clock generator provides the SSC with a separate serial
clock signal. Seven slave select inputs are available for Slave Mode operation. Eight
programmable slave select outputs (chip selects) are supported in Master Mode.

MCB06058_mod

Clock

Control

Address

Decoder

Interrupt

Control

f

SSC

   SSC

 Module

(Kernel)

MRSTB
MTSR

Master

RIR

TIR

EIR

SLSI[7:1]

SLSI[7:1]

SLSO[7:0]

SLSO[7:0]

MRST

MTSR

SCLK

MRSTA

MTSRB
MRST

MTSRA

SCLKB
SCLK

SCLKA

Slave

Slave

Master

Slave

Master

Port

Control

f

CLC

Enable
M/S Select

DMA Requests

SLSOANDO[7:0]

SLSOANDO[7:0]

SLSOANDI[7:0]

Summary of Contents for TC1784















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands