manualshive.com logo in svg

Infineon Technologies TC1784, User Manual

Share
Download
Infineon Technologies TC1784 User Manual Download Page 2276

TC1784

Fast Analog to Digital Converter (FADC)

 

User´s Manual

24-23

V1.1, 2011-05

FADC, V2.21

 

24.2.10

Interrupt Generation

A flexible service request control structure is implemented in the FADC. The FADC
provides the channel conversion request sources and the filter block request sources,
that can be programmed to generate one of four service request output signals SR[3:0].
The service request compressor also makes it possible to assign more than one service
request source to one service request output.

Figure 24-11 Service Request Configuration

All service requests are controlled by an identical control logic. This control logic as
shown in 

Figure 24-12

 provides the following functionality:

•

Service Request Flag

•

Set/Clear Request Flag Control Bits

•

Service Request Enable Bit

•

Service Request Node Pointer

Figure 24-12 Service Request Control Logic

MCA06441_m

Channel

Conversion

Requests

Service

Request

Compressor

Filter Block 0 calculation finished

Channel 2 conversion finished

SR0
SR1
SR2
SR3

Filter

Block

Requests

Channel 3 conversion finished

Filter Block 1 calculation finished

Filter Block 2 calculation finished

Filter Block 3 calculation finished

Channel 0 conversion finished

Channel 1 conversion finished

MCA06442

Request

Flag

CRSR

Set

Service Request
Trigger Signal

Reset

Enable

Bit

CFGRx/FCRn

Reset Req.

Flag Bit

FMR

Set Req.

Flag Bit

01

10

11

00

Node

Pointer

CFGRx/FCRn

To SR0 OR-Gate
To SR1 OR-Gate
To SR2 OR-Gate
To SR3 OR-Gate

≥

1

Summary of Contents for TC1784















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands