Rohde & Schwarz R&S FSP Series, Operating Manual

Page: 711 / 796

Operating Manual 1164.4556.12 - 06 6.317
R&S FSP Remote Control – Description of Commands
Differences in GPIB Behavior between the FSP and the FSE Families of Instruments
R&S
FSP [SENSe<1|2>:]MPOWer[:SEQuence] <analyzer freq>,
<rbw>,
<meas time>,
<trigger source>,
<trigger level>,
<trigger offset>,
<type of meas>,
<# of meas> new function for
R&S FSP
R&S
FSP [SENSe<1|2>:]MPOWer:RESult[:LIST]? new function for
R&S FSP
R&S
FSP [SENSe<1|2>:]MPOWer:RESult:MIN? new function for
R&S FSP
FSE [SENSe<1|2>:]MSUMmary:AHOLd[:STATe] ON | OFF not available for
R&S FSP and FSET
FSE [SENSe<1|2>:]MSUMmary:MODE ABSolute | RELative not available for
R&S FSP and FSET
FSE [SENSe<1|2>:]MSUMmary:MTIMe 0.1S | 1S not available for
R&S FSP and FSET
FSE [SENSe<1|2>:]MSUMmary:REFerence <numeric_value> not available for
R&S FSP and FSET
FSE [SENSe<1|2>:]MSUMmary:REFerence:AUTO ONCE not available for
R&S FSP and FSET
FSE [SENSe<1|2>:]MSUMmary:RUNit PCT | DB not available for
R&S FSP and FSET
FSET [SENSe<1|2>:]PM[:DEViation]:RANGe[:UPPer] <numeric_value> not available for
R&S FSP
R&S
FSP FSE [SENSe<1|2>:]POWer:ACHannel:ACPairs 0 to 3 R&S FSP: new
parameter value 0 for
channel power
measurement
R&S
FSP FSE [SENSe<1|2>:]POWer:ACHannel:
BANDwidth|BWIDth:ACHannel 100 to 1000MHz R&S FSP: parameter
range starts at 100Hz
FSE: parameter range
starts at 0 Hz
R&S
FSP FSE [SENSe<1|2>:]POWer:ACHannel:
BANDwidth|BWIDth:ALTernate<1|2> 100 to 1000MHz R&S FSP: parameter
range starts at 100Hz
FSE: parameter range
starts at 0 Hz
R&S
FSP FSE [SENSe<1|2>:]POWer:ACHannel:
BANDwidth|BWIDth[:CHANnel] 100 to 1000MHz R&S FSP: parameter
range starts at 100Hz
FSE: parameter range
starts at 0 Hz
R&S
FSP FSE [SENSe<1|2>:]POWer:ACHannel:MODE ABSolute | RELative
R&S
FSP FSE [SENSe<1|2>:]POWer:ACHannel:PRESet ACPower | CPOWer |
OBANdwidth | OBWidth |
CN | CN0 | MCACpower MCACpower not
available for FSE
R&S
FSP [SENSe<1|2>:]POWer:ACHannel:PRESet:RLEVel new function for
R&S FSP
Devices Command (Sheet 38 of 47) Parameter Notes