manualshive.com logo in svg

Samsung S3C6400X, User Manual, Page: 47 / 1189

Share
Download
Samsung S3C6400X User Manual Download Page 47

 

PRELIMINARY 

SYSTEM CONTROLLER  

 

S3C6400X RISC MICROPROCESSOR  

3-2

 

 

Preliminary product information describe products that are in development,

 

for which full characterization data and associated errata are not yet available. 
Specifications and information herein are subject to change without notice.

z

 

Control bus priority 

 

FUNCTIONAL DESCRIPTION 

This section describes the functionality of S3C6400X system controller. It covers the clock architecture, reset 
scheme, and power management modes. 

HARDWARE ARCHITECTURE 

Figure 3-1 shows S3C6400X block diagram. S3C6400X consists of ARM1176 processor, several media co-
processors and various peripheral IP’s. ARM1176 processor connected to several memory controllers through 64-
bit AXI-bus to meet bandwidth requirements. Media co-processors, which include MFC (Multi-Format Codec), 
JPEG, Camera interface, TV encoder and etc, are divided into five power domains. The five power domain can be 
controlled independently to reduce unwanted power consumption when the IP’s are not required for an application 
program. 

Scaler

MFC

JPEG

Cam.

I/F

AHB-I

2D

TV

Enc.

AHB-P

LCD

ROT

POST

AHB-F

Security 

System

SDMA

0

SDMA

1

AHB-S1

ARM1176

DOMAIN-V

DOMAIN-I

DOMAIN-P

DOMAIN-F

DOMAIN-S

AXI (64b)

USB
OTG

HS

MMC0

HS

MMC1

AHB-X

Indire

ct 

Host 

IF

USB

Host

Direct

Host 

IF

AHB-T0

DMA0 DMA1

AHB-M0

AXI (32b)

AHB-T1

AHB-M1

AHB-S0

APB (32b)

UART

WDT

RTC

PWM

SYSCON

PCM0

PCM1

IrDA

KeyPAD

TSADC

TZPC

AC97

IIS0

IIS1

IIC

GPIO

HSI Tx

HSI Rx

SPI0

SPI1

HS

MMC2

S-Key

VIC

TZIC

DMC1 DMC0

NF Con.

SROM

OneNAND

CF Con.

ROM

AHB

AHB

DOMAIN-X

DOMAIN-T

DOMAIN-M

MEMSYS

ALIVE

 

Figure 3-1. S3C6400X block diagram 

 

 

Summary of Contents for S3C6400X






































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments