INVT GD350A-004G/5R5P-4 Скачать руководство пользователя страница 8

Страница: 8 / 425

Goodrive350A series high-performance multifunction VFD

Safety precautions

-3-



Protect the VFD against physical shock or vibration during delivery and installation.



Do not carry the VFD by its front cover only as the cover may fall off.



The installation site must be away from children and other public places.



When the installation site altitude exceeds 1000m, derate by 1% for every increase of 100m;

when the installation site altitude exceeds 3000m, consult local INVT dealer or office.



Use the VFD in proper environment. (For details, see "Installation environment".)



Prevent the screws, cables and other conductive parts from falling into the VFD.



As leakage current of the VFD during running may exceed 3.5mA, ground properly and ensure

the grounding resistance is less than 10Ω. The conductivity of PE grounding conductor is the

same as that of the phase conductor (with the same cross sectional area).



R, S and T are the power input terminals, and U, V and W are output motor terminals. Connect

the input power cables and motor cables properly; otherwise, damage to the VFD may occur.

1.4.2 Commissioning and running



Disconnect all power sources applied to the VFD before terminal wiring, and wait

for at least the time designated on the VFD after disconnecting the power

sources.



High voltage presents inside the VFD during running. Do not carry out any

operation on the VFD during running except for keypad setup. The product

control terminals form extra-low voltage circuits. Therefore, you need to prevent

the control terminals from connecting to accessible terminals of other devices.



The VFD may start up by itself when P01.21=1. Do not get close to the VFD and

motor.



The VFD cannot be used as "Emergency-stop device".



The VFD cannot act as an emergency brake for the motor; it is a must to install

mechanical brake device.



During driving a permanent magnet SM, besides above-mentioned items, the

following work must be done before installation and maintenance:

a) Disconnect all the input power sources including main power and control

power.

b) Ensure the permanent-magnet SM has been stopped, and the voltage on

output end of the VFD is lower than 36V.

c) After the permanent-magnet SM stops, wait for at least the time designated

on the VFD, and ensure the voltage b and - is lower than 36V.

d) During operation, ensure the permanent-magnet SM cannot run again by the

action of external load; it is recommended to install effective external brake

device

disconnect

the

direct

electrical

connection

between

permanent-magnet SM and the VFD.

Содержание GD350A-004G/5R5P-4










































































































































































































































































































































































































































Результаты поиска

Содержание GD350A-004G/5R5P-4

Отзывы:

Похожие инструкции для GD350A-004G/5R5P-4

Бренды по названию

Популярные бренды

INVT GD350A-004G/5R5P-4, Руководство по эксплуатации

Результаты поиска

Содержание GD350A-004G/5R5P-4

Отзывы:

Похожие инструкции для GD350A-004G/5R5P-4

Бренды по названию

Популярные бренды