INVT GD350A-004G/5R5P-4 Скачать руководство пользователя страница 373

Страница: 373 / 425

Goodrive350A series high-performance multifunction VFD

Expansion cards

-368-

Indicator

Color

State

Description

Off

The communication between the card and PLC is

offline.

LED3

Red

Failed to set up I/O between the card and PLC.

Blinking (1Hz)

Incorrect PLC configuration.

Blinking (2Hz)

The card failed to send data to the PLC.

Blinking (4Hz)

The connection between the card and PLC timed

out.

Off

No fault.

LED4

Red

3.3V power indicator.

Net port

indicator

Yellow

Link indicator, indicating successful Ethernet

connection.

Off

Link indicator, indicating Ethernet connection not

established.

Net port

indicator

Green

ACK indicator, indicating data interchange being

performed.

Off

ACK indicator, indicating data interchange not be

performed.

Electrical wiring

The EtherNet/IP communication card provides standard RJ45 ports and supports the linear, star, and

ring topologies. The following three figures show the electrical wiring diagrams.

Use CAT5, CAT5e, and CAT6 network cables for electrical wiring. When the communication distance

is greater than 50 meters, use high-quality network cables that meet the high-quality standards.

Master

(PLC)

Slave 1

CN2

CN1

Slave 2

CN2

CN1

Slave

CN2

CN1

Figure A.8 Electrical wiring diagram for a linear topology

Master

(PLC)

Slave 1

CN2

CN1

Slave 2

CN2

CN1

Slave

CN2

CN1

Switch

Figure A.9 Electrical wiring diagram for a star topology

Содержание GD350A-004G/5R5P-4










































































































































































































































































































































































































































Результаты поиска

Содержание GD350A-004G/5R5P-4

Отзывы:

Похожие инструкции для GD350A-004G/5R5P-4

Бренды по названию

Популярные бренды

INVT GD350A-004G/5R5P-4, Руководство по эксплуатации

Результаты поиска

Содержание GD350A-004G/5R5P-4

Отзывы:

Похожие инструкции для GD350A-004G/5R5P-4

Бренды по названию

Популярные бренды