INVT GD350A-004G/5R5P-4 Скачать руководство пользователя страница 2

Страница: 2 / 425

Goodrive350A series high-performance multifunction VFD

Preface

Preface

Thank you for choosing Goodrive350A series variable-frequency drive (VFD).

If not otherwise specified in this manual, the VFD always indicates Goodrive350A series VFD, which

is a high-performance multifunctional VFD that can drive both synchronous motors (SMs) and

asynchronous motors (AMs) and supports torque control, speed control, and position control. The

VFD is armed with advanced vector control technology and the latest digital processor dedicated for

motor control, thus enhancing product reliability and adaptability to the environment. The VFD adopts

customized and industrialized design to realize excellent control performance through optimized

functions and flexible applications.

In order to meet diversified customer demands, the VFD provides abundant expansion cards

including programmable expansion card, PG card, communication card and I/O expansion card to

achieve various functions as needed. Each VFD can be installed with three expansion cards at most.

The programmable expansion card adopts the mainstream development environment for customers

to carry out secondary development easily, fulfilling varied customized needs and reducing customer

cost.

The PG card supports a variety of encoders like incremental encoders and resolver-type encoders. In

addition, it also supports pulse reference and frequency-division output. The PG card adopts digital

filter technology to improve EMC performance and to realize stable transmission of the encoder

signal over a long distance. It is equipped with encoder offline detection function to contain the impact

of system faults.

The VFD supports multiple kinds of popular communication modes to realize complicated system

solutions. It can be connected to the internet with optional wireless communication card, by which you

can monitor the VFD state anywhere any time through mobile App.

The VFD uses high power density design. Some power ranges carry built-in DC reactor and braking

unit to save installation space. Through overall EMC design, it can satisfy the low noise and low

electromagnetic interference requirements to cope with challenging grid, temperature, humidity and

dust conditions, thus greatly improving product reliability.

This operation manual presents installation wiring, parameter setup, fault diagnosis and trouble

shooting, and precautions related to daily maintenance. Read through this manual carefully before

installation to ensure the VFD is installed and operated in a proper manner to give full play to its

excellent performance and powerful functions.

If the product is ultimately used for military affairs or manufacture of weapon, it will be listed on the

export control formulated by Foreign Trade Law of the People's Republic of China. Rigorous review

and necessary export formalities are needed when exported.

We reserve the right to update the manual information without prior notice and have the final

interpretation for the manual content.

Содержание GD350A-004G/5R5P-4










































































































































































































































































































































































































































Результаты поиска

Содержание GD350A-004G/5R5P-4

Отзывы:

Похожие инструкции для GD350A-004G/5R5P-4

Бренды по названию

Популярные бренды

INVT GD350A-004G/5R5P-4, Руководство по эксплуатации

Результаты поиска

Содержание GD350A-004G/5R5P-4

Отзывы:

Похожие инструкции для GD350A-004G/5R5P-4

Бренды по названию

Популярные бренды