INVT GD350A-004G/5R5P-4 Скачать руководство пользователя страница 313

Страница: 313 / 425

Goodrive350A series high-performance multifunction VFD

Troubleshooting

-308-

difference between two actions need to be longer than 20 ms. For example, 1s, 0.5s, and 0.2s.

(3)

For circuits in VFD systems, electromagnetic RCDs are recommended. Electromagnetic RCDs

have strong anti-interference capability, and thus can prevent the impact of high-frequency

leakage current.

Electronic RCD

Electromagnetic RCD

Low cost, high sensitivity, small in volume,

susceptible to voltage fluctuation of the grid

and ambient temperature, weak

anti-interference capability

Requiring highly sensitive, accurate, and

stable zero-phase sequence current

transformer, using permalloy

high-permeability materials, complex process,

high cost, not susceptible to voltage

fluctuation of the power supply and ambient

temperature, strong anti- interference

capability

2. Solution to RCD misoperation (handling the VFD)

Try to remove the jumper cap at "EMC/J10" on the middle casing of the VFD.

Try to reduce the carrier frequency to 1.5 kHz (P00.14=1.5).

Try to modify the modulation mode to "3PH modulation and 2PH modulation" (P08.40=0).

3. Solution to RCD misoperation (handling the system power distribution)

(1) Check and ensure that the power cable is not soaking in water.

(2) Check and ensure that the cables are not damaged or spliced.

(3) Check and ensure that no secondary grounding is performed on the neutral wire.

(4) Check and ensure that the main power cable terminal is in good contact with the air switch or

contactor (all screws are tightened).

(5) Check 1PH powered devices, and ensure that no earth lines are used as neutral wires by these

devices.

Do not use shielded cables as VFD power cables and motor cables.

7.7.5 Live device chassis

After the VFD is started, there is sensible voltage on the chassis, and you may feel an electric shock

when touching the chassis. The chassis, however, is not live (or the voltage is far lower than the

human safety voltage) when the VFD is powered on but not running.

Solution

1. If there is power distribution grounding or ground stud on the site, ground the cabinet chassis of

the drive system through the power ground or stud.

If there is no grounding on the site, you need to connect the motor chassis to the ground terminal PE

of the VFD, and ensure that the jumper at "EMC/J10" on the middle casing of the VFD is shorted.

Содержание GD350A-004G/5R5P-4










































































































































































































































































































































































































































Результаты поиска

Содержание GD350A-004G/5R5P-4

Отзывы:

Похожие инструкции для GD350A-004G/5R5P-4

Бренды по названию

Популярные бренды

INVT GD350A-004G/5R5P-4, Руководство по эксплуатации

Результаты поиска

Содержание GD350A-004G/5R5P-4

Отзывы:

Похожие инструкции для GD350A-004G/5R5P-4

Бренды по названию

Популярные бренды