INVT GD350A-004G/5R5P-4 Скачать руководство пользователя страница 353

Страница: 353 / 425

Goodrive350A series high-performance multifunction VFD

Expansion cards

-348-

GPRS card

–IC501-2

A.2 Dimensions and installation

All expansion cards are of the same dimensions (108 mm × 39 mm) and can be installed in the same

way.

Comply with the following operation principles when installing or removing an expansion card:

1. Ensure that no power is applied before installing an expansion card.

2. An expansion card can be installed into a respective card slot among SLOT1, SLOT2, and SLOT3.

3. VFDs of 5.5 kW or lower can be configured with two expansion cards at the same time, and those

of 7.5 kW or higher can be configured with three expansion cards.

4. If interference occurs on the external wires after expansion cards are installed, change their

installation card slots flexibly to facilitate the wiring. For example, the connector of the connection

cable of the DP card is large, so it is recommended to be installed in the SLOT1 card slot.

5. To ensure high anti-interference capability in closed-loop control, you need to use a shielding wire

in the encoder cable and ground the two ends of the shielding wire, that is, connect the shielding

layer to the housing of the motor on the motor side, and connect the shielding layer to the PE

terminal on the PG card side.

Note:

For 2.2

–5.5kW models, the 24V power suply card can be inserted into SLOT1; for 7.5kW and

higher models, the 24V power supply card can be inserted into SLOT1 or SLOT3; for 11kW and

higher models, the 24V power supply card can be inserted into any of the three slots.

Figure A.1 shows the installation diagram and a VFD with expansion cards installed.

Содержание GD350A-004G/5R5P-4










































































































































































































































































































































































































































Результаты поиска

Содержание GD350A-004G/5R5P-4

Отзывы:

Похожие инструкции для GD350A-004G/5R5P-4

Бренды по названию

Популярные бренды

INVT GD350A-004G/5R5P-4, Руководство по эксплуатации

Результаты поиска

Содержание GD350A-004G/5R5P-4

Отзывы:

Похожие инструкции для GD350A-004G/5R5P-4

Бренды по названию

Популярные бренды