INVT GD350A-004G/5R5P-4 Скачать руководство пользователя страница 6

Страница: 6 / 425

Goodrive350A series high-performance multifunction VFD

Safety precautions

-1-

1 Safety precautions

1.1 What this chapter contains

Read this manual carefully and follow all safety precautions before moving, installing, operating and

servicing the VFD. If these safety precautions are ignored, physical injury or death may occur, or

damage may occur to the equipment.

If any physical injury or death or damage to the equipment occur due to neglect of the safety

precautions in the manual, our company will not be responsible for any damages and we are not

legally bound in any manner.

1.2 Safety definition

Danger

: Severe personal injury or even death can result if related requirements are not followed.

Warning

: Personal injury or equipment damage can result if related requirements are not followed.

Note

: Actions taken to ensure proper running.

Trained and qualified professionals

: People working on the VFD must have received professional

electrical and safety training and obtained the certificates, and must be familiar with all steps and

requirements of VFD installing, commissioning, running and maintaining and capable to prevent any

emergencies.

1.3 Warning symbols

Warnings caution you about conditions which can result in serious injury or death and/or damage to

the equipment, and advice on how to avoid the danger. Following warning symbols are used in this

manual.

Symbols

Name

Instruction

Abbreviation

Danger

Serious physical injury or even death

may occur if related requirements are

not followed

Warning

Physical injury or damage to the

equipment may occur if related

requirements are not followed

Forbid

Electrostatic

discharge

The PCBA may be damaged if

related requirements are not followed

Hot

Hot sides

The VFD base may become hot. Do

not touch.

Electric

shock

As high voltage still presents in the

bus capacitor after power off, wait for

at least five minutes (or 15 min / 25

min, depending on the warning

Содержание GD350A-004G/5R5P-4










































































































































































































































































































































































































































Результаты поиска

Содержание GD350A-004G/5R5P-4

Отзывы:

Похожие инструкции для GD350A-004G/5R5P-4

Бренды по названию

Популярные бренды

INVT GD350A-004G/5R5P-4, Руководство по эксплуатации

Результаты поиска

Содержание GD350A-004G/5R5P-4

Отзывы:

Похожие инструкции для GD350A-004G/5R5P-4

Бренды по названию

Популярные бренды