•
for a TFTP server, enter
tftp://hostip/filepath/filename
where
hostip is either an IPv4 dotted decimal address or an IPv6 URI
[x:x:x:x::x] format address.
Defaults
If no URL is specified, FTOS uses the boot flash image that was packed with it.
Command Modes
EXEC Privilege
Command History
Version 7.7.1.0
Introduced the
system-image
option.
Version 7.5.1.0
Introduced on the C-Series.
E-Series
Original command
Usage
Information
RFC 3986 specifies that IPv6 host addresses in a uniform resource identifier (URI) should be
enclosed in square brackets, [X:X:X:X::X]. For maximum flexibility, this command accepts IPv6
host addresses with or without the square brackets.
A system message appears stating the Bootflash upgrade status. Reload the system to boot
from the upgraded boot images.
After the URL is specified, you can use the same downloaded image for upgrading an individual
RPM, line cards, SFM FPGA, and system-image for cache-boot without specifying the file-url
again using the command upgrade {
bootflash-image | bootselector-image |
system-image
} {
all | linecard linecard-slot | rpm
}. After 20 minutes, the
cached memory is released and returned for general use, but the URL is maintained and you do
not have to specify it for subsequent upgrades.
Related
Commands
upgrade fpga-image
– upgrades the FPGA version in the specified E-Series SFM.
boot system
– displays the configured boot image information.
upgrade (E-Series version)
Upgrade the bootflash, boot selector, or system image on a processor.
E-Series
Syntax
upgrade {bootflash-image | bootselector-image | system-image}
{all | linecard
linecard-slot
| rpm} {booted |
file-url
}
Parameters
bootflash-image
Enter the keyword
bootflash-image
to upgrade the bootflash
image.
bootselector-
image
Enter the keyword
bootselector-image
to upgrade the boot
selector image. Use with technical assistance center (TAC)-
supervision only.
system-image
Enter the keyword
system-image
to upgrade the cache boot
image.
94
Содержание Force10 S4810P
