network area
Define which interfaces run OSPF and the OSPF area for those interfaces.
C-Series, E-Series, S-Series, Z-Series, S4810
Syntax
network
ip-address mask
area
area-id
To disable an OSPF area, use the
no network
ip-address mask
area
area-id
command.
Parameters
ip-address
Specify a primary or secondary address in dotted decimal format. The
primary address is required before adding the secondary address.
mask
Enter a network mask in /prefix format. (/x)
area-id
Enter the OSPF area ID as either a decimal value or in a valid IP
address. Decimal value range is 0 to 65535. IP address format is
dotted decimal format A.B.C.D.
NOTE: If the area ID is smaller than 65535, it is converted to a
decimal value. For example, if you use an area ID of 0.0.0.1, it is
converted to 1.
Command Modes
ROUTER OSPF
Command History
Version 8.3.11.1
Introduced on the Z9000.
Version 8.3.7.0
Introduced on the S4810.
Version 7.8.1.0
Introduced to all platforms.
Version 7.6.1.0
Introduced on the S-Series.
Version 7.5.1.0
Introduced on the C-Series.
pre-Version
6.1.1.1
Introduced on the E-Series.
Usage
Information
To enable OSPF on an interface, the
network area
command must include, in its range of
addresses, the primary IP address of an interface.
NOTE: An interface can be attached only to a single OSPF area.
If you delete all the network area commands for Area 0, the
show ip ospf
command
output will not list Area 0.
passive-interface
Suppress both receiving and sending routing updates on an interface.
C-Series, E-Series, S-Series, Z-Series, S4810
Syntax
passive-interface {default |
interface
}
1171
Содержание Force10 S4810P
