Time since last interface status change: 00:05:12
Related
Commands
show interfaces configured
– displays any interface with a non-default configuration.
show interfaces linecard
– displays information on all interfaces on a specific line card.
show interfaces phy
show interfaces rate
– displays information of either rate limiting or rate policing on the
interface.
show interfaces switchport
– displays Layer 2 information about the interfaces.
show inventory (C-Series and E-Series)
– displays the chassis type, components (including
media), FTOS version including hardware identification numbers, and configured protocols.
show inventory (S-Series and Z-Series)
– displays the S-Series and Z-Series switch types,
components (including media), FTOS version including hardware identification numbers, and
configured protocols.
show ip interface
– displays Layer 3 information about the interfaces.
show linecard
– displays the line card(s) status.
show range
– displays all interfaces configured using the interface range command.
show interfaces configured
Display any interface with a non-default configuration.
C-Series, E-Series, S-Series, Z-Series, S4810
Syntax
show interfaces configured
Command Modes
•
EXEC
•
EXEC Privilege
Command History
Version 8.3.11.1
Introduced on the Z9000.
Version 8.3.7.0
Introduced on the S4810.
Version 8.1.1.0
Introduced on the E-Series ExaScale.
Version 7.6.1.0
Introduced on the S-Series.
Version 7.5.1.0
Introduced on the C-Series.
Version 6.4.1.0
Changed the organization of the display output.
Example
FTOS#show interfaces configured
GigabitEthernet 13/18 is up, line protocol is up
Hardware is Force10Eth, address is 00:01:e8:05:f7:fc
Current address is 00:01:e8:05:f7:fc
Interface index is 474791997
Internet address is 1.1.1.1/24
MTU 1554 bytes, IP MTU 1500 bytes
LineSpeed 1000 Mbit, Mode full duplex, Master
ARP type: ARPA, ARP Timeout 04:00:00
Last clearing of "show interfaces" counters 00:12:42
Queueing strategy: fifo
Input Statistics:
795
Содержание Force10 S4810P
