49
Simple Network Management Protocol (SNMP)
and Syslog
This chapter contains commands to configure and monitor the simple network management protocol (SNMP) v1/v2/v3
and Syslog. Both features are supported on the following platforms: C-Series, E-Series, S-Series, Z-Series, S4810.
The chapter contains the following sections:
•
SNMP Commands
•
Syslog Commands
SNMP Commands
The following SNMP commands are available in the Dell Force10 operating software (FTOS).
The simple network management protocol (SNMP) is used to communicate management information between the
network management stations and the agents in the network elements. FTOS supports SNMP versions 1, 2c, and 3,
supporting both read-only and read-write modes. FTOS sends SNMP traps, which are messages informing an SNMP
management system about the network. FTOS supports up to 16 SNMP trap receivers.
Important Points to Remember
•
Typically, 5-second timeout and 3-second retry values on an SNMP server are sufficient for both LAN and WAN
applications. If you experience a timeout with these values, the recommended best practice on Dell Force10
switches (to accommodate their high port density) is to increase the timeout and retry values on your SNMP
server to the following:
– SNMP Timeout—greater than 3 seconds.
– SNMP Retry count—greater than 2 seconds.
•
If you want to query an E-Series switch using SNMP v1/v2/v3 with an IPv6 address, configure the IPv6 address
on a non-management port on the switch.
•
If you want to send SNMP v1/v2/v3 traps from an E-Series using an IPv6 address, use a non-management port.
•
SNMP v3 informs are not currently supported with IPv6 addresses.
•
If you are using access control lists (ACLs) in an SNMP v3 configuration, group ACL overrides user ACL if the
user is part of that group.
•
SNMP operations are not supported on a virtual local area network (VLAN).
show snmp
Display the status of SNMP network elements.
C-Series, E-Series, S-Series, Z-Series
Syntax
show snmp
1479
Содержание Force10 S4810P
