manualshive.com logo in svg

NXP Semiconductors freescale KV4 Series, Reference Manual

Share
Download
NXP Semiconductors freescale KV4 Series Reference Manual Download Page 428

1

eDMA  Engine

Data Path

eDMA

0

Program Model/

64

Control

n-1

To/F

rom Cr

ossbar S

witch

2

Channel Arbitration

Address Path

Read Data

Write Data

Address

Read Data

Write Data

Write Address

eDMA Peripheral

Request

eDMA Done

Transfer
Control
Descriptor (TCD)

Int

er

nal P

er

ipher

al Bus

Figure 23-292. eDMA operation, part 3

23.4.2 Fault reporting and handling

Channel errors are reported in the Error Status register (DMAx_ES) and can be caused
by:

• A configuration error, which is an illegal setting in the transfer-control descriptor or

an illegal priority register setting in Fixed-Arbitration mode, or

• An error termination to a bus master read or write cycle

A configuration error is reported when the starting source or destination address, source
or destination offsets, minor loop byte count, or the transfer size represent an inconsistent
state. Each of these possible causes are detailed below:

• The addresses and offsets must be aligned on 0-modulo-transfer-size boundaries.
• The minor loop byte count must be a multiple of the source and destination transfer

sizes.

Functional description

KV4x Reference Manual, Rev. 2, 02/2015

428

Preliminary

Freescale Semiconductor, Inc.

Summary of Contents for freescale KV4 Series
















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands