112
Parameters
authentication-failure
: Specifies notifications about authentication failures on an interface.
bad-packet
: Specifies notifications about error messages received on an interface.
config-error
: Specifies notifications about error configuration of an interface.
grhelper-status-change
: Specifies notifications about GR helper state change.
grrestarter-status-change
: Specifies notifications about GR restarter state change.
if-state-change
: Specifies notifications about interface state change.
lsa-maxage
: Specifies LSA max age notifications.
lsa-originate
: Specifies notifications about locally generated LSAs.
lsdb-approaching-overflow
: Specifies notifications about approaching LSDB overflows.
lsdb-overflow
: Specifies LSDB overflow notifications.
neighbor-state-change
: Specifies notifications about neighbor state change.
nssatranslator-status-change
: Specifies notifications about NSSA translator state
change.
retransmit
: Specifies notifications about packets that are received and forwarded on an
interface.
virt-authentication-failure
: Specifies notifications about authentication failures on a
virtual interface.
virt-bad-packet
: Specifies notifications about error messages received on a virtual interface.
virt-config-error
: Specifies notifications about error configuration of a virtual interface.
virt-retransmit
: Specifies notifications about packets that are received and forwarded on a
virtual interface.
virtgrhelper-status-change
: Specifies notifications about neighbor GR helper state
changes of a virtual interface.
virtif-state-change
: Specifies notifications about virtual interface state change.
virtneighbor-state-change
: Specifies notifications about the neighbor state change of a
virtual interface.
Examples
# Disable SNMP notifications for OSPF.
<Sysname> system-view
[Sysname] undo snmp-agent trap enable ospf
spf-schedule-interval (OSPF view)
Use
spf-schedule-interval
to set the OSPF SPF calculation interval.
Use
undo spf-schedule-interval
to restore the default.
Syntax
spf-schedule-interval
maximum-interval
[
minimum-interval
[
incremental-interval
]
]
undo spf-schedule-interval
Summary of Contents for SOHO IE4300
